eMachines 1stMainboard AM37 Manual Download Page 47

Page: 47 / 51

3 - 19

BIOS Setup

Reset Configuration Data

Enabling it to reset the system Extended System Configuration Data (ESCD)

when you exit Setup if you have installed a new add-on card and the

system reconfiguration has caused such a serious conflict that the operat-

ing system can not boot. The options are: Disabled, Enabled.

PNP OS Installed

If your operating system is a Plug-and-Play one, such as Windows NT,

Windows 95, select Yes. The options are: No, Yes.

PnP/PCI Configurations

Resources Controlled By

If set at Auto, the BIOS arranges all system resources. If there exists con-

flict, select Manual. The options are: Auto (ESCD), Manual.

The manual options of

IRQ- / DMA

- assigned to are: PCI/ISA PnP, Legacy

ISA.

PCI/VGA Palette Snoop

Set this feature to be enabled if any ISA adapter card installed in the

system requires the VGA palette snoop function.

The options are: Disabled, Enabled.

Summary of Contents for 1stMainboard AM37




















































Search results

Summary of Contents for 1stMainboard AM37

Reviews:

Related manuals for 1stMainboard AM37

Brands by name

Popular brands

eMachines 1stMainboard AM37, Manual

Search results

Summary of Contents for 1stMainboard AM37

Reviews:

Related manuals for 1stMainboard AM37

Brands by name

Popular brands