elysia skulpter 500 Manual Download Page 12

Page: 12 / 16

Technical Details

Frequency response @ 3dB gain:

10Hz - 170kHz (-3dB)

Frequency response @ 29dB gain:

10Hz - 170kHz (-3dB)

THD+N @ +6dBu level, 3dB gain, 20Hz - 22kHz:

0.007%

THD+N @ +6dBu level, 29dB gain, 20Hz - 22kHz:

0.007%

Noise floor @ 3dB gain, 20Hz - 20kHz (A-weighted): -97dBu

Noise floor @ 29dB gain, 20Hz - 20kHz (A-weighted): -93dBu

CMRR @ +6dBu level, 29dBu gain, 1kHz:

87dB

CMRR @ +6dBu level, 29dBu gain, 10kHz:

69dB

Maximum level Mic In/DI In/Out

19/19/21dBu

Impedance Mic In/DI In/Out

13.6kohm/1megohm/62ohm

CE Conformity

elysia GmbH, Am Panneschopp 18, 41334 Nettetal, Ger-

many, declares with sole responsibility that this product

complies with the following norms and directives:

•

2006/95/EG Low Voltage Directive (formerly 73/23/EWG or

93/68/EWG)

•

89/336/EWG EMC (Electromagnetic Compatibility) Directive

•

DIN EN 55103-1 EMC of audio equipment - Emission

•

DIN EN 55103-2 EMC of audio equipment - Immunity

This declaration becomes invalid by any unapproved modifi-

cation of the device.

Nettetal, 01.05.2018 - Ruben Tilgner & Dominik Klaßen

Summary of Contents for skulpter 500

















Search results

Summary of Contents for skulpter 500

Reviews:

Related manuals for skulpter 500

Brands by name

Popular brands

elysia skulpter 500, Manual

Search results

Summary of Contents for skulpter 500

Reviews:

Related manuals for skulpter 500

Brands by name

Popular brands