background image

 

User’s manual r.0805 EQ45 (EN) 

www.elyq.com 

Page 4/21

 

 

By handling, charging or using the included Li-Po battery you assume all risks associated with lithium batteries. If you 
do not agree with these conditions, return your complete EQ.45 model in new, unused condition to the place of 
purchase immediately. 
You must charge the included 11.1V 100mAh 3-cell Li-Po battery pack in a safe area away from flammable materials. 

9

 

Do not charge the battery when installed in the helicopter. 

9

  Never charge the battery unattended. When charging the battery you should always remain in constant 

observation to monitor the charging process and react to potential problems that may occur. 

9

 

After flight, the battery must be cooled to ambient temperature before charging. 

9

 

You MUST use the included 3-cell Li-Po Balance Charger ONLY

. Failure to do so may result in a fire 

causing personal injury and/or property damage. 

DO NOT use a Ni-Cd or Ni-MH charger.

 

9

  If at any time during the charge or discharge process the battery begins to balloon or swell, stop charging or 

discharging immediately. Quickly and safely disconnect the battery, then place it in a safe, open area away 
from flammable materials to observe it for at least 15 minutes. Continuing to charge or discharge a battery that 
has begun to balloon or swell can result in a fire. A battery that has ballooned or swollen even a small amount 
must be removed from service completely. 

9

  In the event of a crash, you must quickly and safely disconnect and remove the battery from the model, then 

place it in a safe, open area away from flammable materials to observe it for at least 15 minutes. 

9

 

Store the battery at room temperature for best results. 

9

  When transporting or temporarily storing the battery, the temperature range should be from 5–50 degrees 

Celsius. Do not store the battery or model in a car or direct sunlight whenever possible. If stored in a hot car, 
the battery can be damaged or even cause a fire. 

9

  Do not over-discharge the battery. Discharging the battery too low can cause damage to the pack resulting in 

reduced performance and duration.  

If you have any further questions or concerns regarding the handling, charging and/or use of the included Li-Po battery 
pack, please contact ElyQ’s Product Support staff. 

It is important that you only charge the included 11.1V 1200mAh 3-cell Li-Po Battery Pack with the included 3-
cell 11.1V Li-Po Balance Charger. Your battery pack is equipped with special Charge Protection Circuitry and a 
Balance Charge Lead with connector that is only compatible with this charger. Attempting to charge the pack 
using another Li-Po charger or non Li-Po compatible charger could result in serious damage. Please 
familiarize yourself thoroughly with the warnings and guidelines before continuing. 
Note

: The Li-Po battery pack included with your EQ.45 will arrive partially charged. For this reason the initial charge 

may only take approximately one hour. 
The included 3-cell 11.1V Li-Po Balance Charger will charge a near fully discharged (not over-discharged) 11.1V 
1200mAh 3-cell Li-Po Battery Pack in approximately 2.0–2.5 hours. In some cases the charge time may be shorter 
depending on the actual amount of capacity left in the pack after a flight. 

NEVER charge the battery unattended. 

The charger requires up to 1.5 Amps of 11.5–15 Volt DC input power that can be supplied from a small 12V gel  cell or 
car battery. Input power for the charger can also be supplied through the use of an AC to DC adapter/power supply for 
convenient charging anywhere an AC outlet is available. 

NEVER attempt to power the charger from an AC outlet 

without the use of a proper AC to DC adapter/power supply.

 

Safety precautions 

The Failure to follow these safety precautions may result in severe injury to yourself and others. 

Keep your face and body as well as all spectators away from the plane of rotation of the rotors whenever the battery is 
connected. 

Keep these items away from the rotors: loose clothing. Shirt sleeves. ties. scarfs. long hair or loose objects such as 
pencils or screwdrivers that may fall out of shirt or jacket pockets into the rotors . 

The spinning blades of a model helicopter can cause serious injury. When choosing a flying site for your EQ.45, stay 
clear of buildings. trees and power lines. AVOID flying in or near crowded areas. DO NOT fly close to people. children 
or pets . Maintain a safe pilot-to-helicopter distance while flying. 

9

  Your EQ.45 RTF should not be considered a toy ,but rather a sophisticated, working model that functions very 

much like a full-size helicopter. Because of its performance capabilities, the EQ.45, if not assembled and 
operated correctly, could possibly cause injury to yourself or spectators and damage to property. 

9

  You must check the operation of the model before 

every 

flight to insure that all equipment is operating and 

that the model has remained structurally sound. Be sure to check linkages or other connectors often and 
replace them if they show any signs of wear or fatigue. 

9

 

If you are not an experienced pilot or have not flown this type of model before, we recommend that you get the 
assistance of an experienced pilot in your club for your first flights. lf you're not a member of a club, your local 
hobby shop has information about clubs in your area whose membership includes experienced pilots. 

We, as the manufacturer, provide you with a top quality, thoroughly tested helicopter and instructions, but ultimately the 
quality and flyability of your finished model depends on how you build it; therefore, we cannot in any way guarantee the 
performance of your completed model, and no representations are expressed or implied as to the performance or 
safety of your completed model. 

Summary of Contents for EQ.45






















Reviews: