background image

 

 

CMi6160 

User’s Manual English 

 

 

 

 

 

 

 

 

 

 

 

 

CMi6160 

User’s Manual English 

page | 15 (38) 

[2022-10] 

 

v1.4 

 

 

 

 

Op. 

LwM2M object 

LwM2M resource 

ID 

Type 

Range or 
Enumeration 

Comment 

Elvaco NB-IoT 
Status 

ECL 

33907/0/

Integer 

0..2 

 

Elvaco NB-IoT 
Status 

RSSI 

33907/0/

Integer 

 

[dBm *10] 

Elvaco NB-IoT 
Status 

SNR 

33907/0/

Integer 

 

[dB*10] 

Elvaco NB-IoT 
Status 

MDM connection 
status 

33907/0/
10 

Integer 

 

0: OK

 

1: Connecting

 

2: No 
credentials 
3: DTLS 
Rejected

 

4: MQTT-SN 
F

ailed 

5: MQTT-SN 
Rejected 

Elvaco Meter 
Info 

Meter Model 

33908/0/

String 

 

Elvaco Meter 
Info 

Meter ID 

33908/0/

Integer 

 

 

Elvaco Meter 
Info 

Comm status 

33908/0/

Integer 

 

0: OK 
1: No meter 
detected 
2: Error 

Elvaco Meter 
Info 

Error flags 

33908/0/

Opaque 

 

Meter Error flags 

Elvaco NB-IoT 
Info 

IMSI 

33909/0/

Integer 

 

SIM IMSI 

Elvaco NB-IoT 
Info 

ICCID 

33909/0/

Integer 

 

SIM ICCID 

Elvaco NB-IoT 
Info 

Registrations 

33909/0/

Integer 

 

NB-IoT 
Registrations 

Elvaco NB-IoT 
Info 

Last Registration 
duration 

33909/0/

Integer 

 

NB-IoT Last 
Regsitration 
Duration 

Elvaco NB-IoT 
Info 

Modem Model 

33909/0/

String 

 

NB-IoT Modem 
Model 

Elvaco NB-IoT 
Info 

Modem Firmware 

33909/0/

String 

 

NB-IoT Modem 
Firmware 

Table 1: CMi6160 status/configuration parameters 

 

 

Summary of Contents for 1100450







































Reviews: