www.elura.audio
MSTR
model M-B6.5Z.2
black label series
2-way In-Ceiling Speaker System
Warranty
All Elura products come with a limited
lifetime
liability warranty. This warranty
includes
parts and labor repairs on all
components found to be defective in
material
or workmanship under normal
conditions of use. This warranty shall
not
apply to products which have been
abused, modified or disassembled.
A speaker that fails under conditions
other than those covered will be re
-
paired at the current price of parts and
labor in effect at the time of repair. Such
repairs are warranted for 90 days from
the day of reshipment to the BUYER. If
the unit is delivered by mail, customers
agree to insure the unit or assume the
risk of loss or damage in transit.
Under no circumstances will a unit be
accepted without a return authorization
number. The warranty is in lieu of all
other warranties expressed or implied,
including without limitations, any other
implied warranty or fitness or mer
-
chantability for any particular purpose,
all of which are expressly disclaimed.
Proof of sale may be required in order to
claim warranty.
Specifications
• Max. Power Handling: 5 - 70 Watts
• Sensitivity: 91dB @ 1 watt/1 meter
• Freq. Response: 55 Hz-20,000 Hz
• Driver Complement: 6
1
/
2
˝ (165mm)
compression molded mineral filled
polymer cone woofer with rubber
surround
1
/
2
˝ (13mm) zero-diffraction, pivoting,
liquid-cooled PEI dome tweeter
• Nominal Impedance: 8 ohms
• Overall Dimensions: 9.25˝ (diameter)
round x 4.23˝
D (235mm x 107mm)
• Required Ceiling Cutout:
8.25˝
(diameter) round (210mm)
Continued from front
(Grille painting hint: Use a paint roller
that is nearly out of paint to first paint
the inside of the grille, then the out-
side. This will avoid paint filling the
grille perforations.)
5.
Attach the wire to the input termi
-
nals on the rear of the speaker.
Remember to maintain proper
polarity with the amplifier by
attaching the positive (+) lead to
the
red terminal and the negative (-)
lead
to the black terminal.
6.
See Fig. 6. With the speaker wire
attached to the speaker, slide the
speaker up inside the cutout hole.
Center the speaker in the cutout
hole
and turn the four locking screws
clockwise until the speaker is drawn
up snugly to the wall board from be
-
hind, clamping the speaker in place.
Try to tighten each screw equally.
Replace the speaker grille by gently
placing it over the speaker until the
magnets “grab” hold of the grille.
New Construction
1. Determine speaker locations and
mark them on your plans for future
reference.
2. If possible, run speaker wires after
HVAC and electrical wiring is in place.
3. Secure speaker wires in place
along the run with insulated staples
only and be careful not to pierce the
wire’s insulation. Allow a bit of slack for
expansion of building materials.
4. Needless to say, the actual
speakers should not be installed until
the wall board is in place. In the
meantime, leave several feet of wire
coiled up and secured at the back
side of the mounting hole.
5. To complete the installation follow
steps 2 through 5 above.
Operational Check
After making all connections
,
it’s a
good idea
to make sure everything is
working properly.
Turn on your sur-
round or stereo system making sure
the volume control is turned down
and that the balance control is in the
center position. Activate a musical or
movie source such as FM, a CD or
DVD player. Gently turn up the vol
-
ume, you should hear sound coming
from your new speakers. If no sound
is heard from any or all speakers,
switch off the system immediately
and check for open or loose connec
-
tions, wrong polarity or shorts,
or
improper source selection.
FIG. 6
FIG. 4
FIG. 5
Optional back can
