background image

11

REPLACEMENT PARTS

When servicing use only identical replacement parts. 

SERVICE AND REPAIRS

All quality tools will eventually require servicing, or replacement of parts due to
wear from normal use. All repairs made by the service centers are fully
guaranteed against defective material and workmanship. We cannot guarantee
repairs made or attempted by others.

Should you have any questions about your tool, call 1-800-54-HOW-TO (544-
6986) or feel free to write us at any time. In any communications, please give all
information shown on the nameplate of your tool (model number, type, serial
number, etc.). 

SERVICE

Recommended accessories for use with your tool are available at extra cost from
your distributor or local service center. 
ACCESSORY MUST BE RATED FOR USE AT SPEED EQUAL TO OR
HIGHER THAN NAMEPLATE R.P.M. OF TOOL WITH WHICH IT IS BEING
USED.

The use of any non-recommended accessory may be
hazardous.

Elu industrial tools are warranted for one year from date of purchase. We will
repair, without charge, any defects due to faulty materials or workmanship. For
warranty repair information, call your local Black & Decker service center. This
warranty does not apply to accessories or damage caused where repairs have
been made or attempted by others. This warranty gives you specific legal rights
and you may have other rights which vary in certain states or provinces.
In addition to the warranty, ELU tools are covered by our:

30 DAY NO RISK SATISFACTION GUARANTEE

If you are not completely satisfied with the performance of your ELU power tool,
simply return it to the participating seller within 30 days for a full refund. Please
return the complete unit, transportation prepaid. Proof of purchase may be
required.

ACCESSORIES

WARRANTY

Summary of Contents for ELU27158

















Reviews: