ELTEX WEP-2L User Manual Download Page 52 | Manualshive

Page: 52 / 65

background image

WEP-2L. User manual

52

6.3.4 Configuration of VAP with Captive Portal

Commands to configure portal authorization by sending your account to the Radius server

WEP-2L(root):/#

configure

WEP-2L(config):/#

interface

WEP-2L(config):/interface#

wlan1-va0

WEP-2L(config):/interface/wlan1-va0#

common

WEP-2L(config):/interface/wlan1-va0/common#

enabled true

WEP-2L(config):/interface/wlan1-va0/common#

exit

WEP-2L(config):/interface/wlan1-va0#

vap

WEP-2L(config):/interface/wlan1-va0/vap#

vlan-id X

(where X - VLAN-ID on VAP)

WEP-2L(config):/interface/wlan1-va0/vap#

security-mode off

(Encryption mode off - Without password)

WEP-2L(config):/interface/wlan1-va0/vap#

ssid 'Portal_WEP-2L'

(Change SSID name)

WEP-2L(config):/interface/wlan1-va0/vap#

captive-portal

WEP-2L(config):/interface/wlan1-va0/vap/captive-portal#

scenarios

WEP-2L(config):/interface/wlan1-va0/vap/captive-portal/scenarios#

scenario-redirect

WEP-2L(config):/interface/wlan1-va0/vap/captive-portal/scenarios/scenario-redirect#

redirect-url http://

<IP>:<PORT>/eltex_portal/

(Specify virtual portal URL)

WEP-2L(config):/interface/wlan1-va0/vap/captive-portal/scenarios/scenario-redirect#

index 1

WEP-2L(config):/interface/wlan1-va0/vap/captive-portal/scenarios/scenario-redirect#

virtual-portal-name

default

(Specify portal name. By default: default)

WEP-2L(config):/interface/wlan1-va0/vap/captive-portal/scenarios/scenario-redirect#

exit

WEP-2L(config):/interface/wlan1-va0/vap/captive-portal/scenarios#

exit

WEP-2L(config):/interface/wlan1-va0/vap/captive-portal#

enabled true

WEP-2L(config):/interface/wlan1-va0/vap/captive-portal#

exit

WEP-2L(config):/interface/wlan1-va0/vap#

radius

WEP-2L(config):/interface/wlan1-va0/vap/radius#

domain root

(where root - User domain)

WEP-2L(config):/interface/wlan1-va0/vap/radius#

acct-enable true

(Enable the sending of «Accounting»

messages to the RADIUS server. By default: false)

WEP-2L(config):/interface/wlan1-va0/vap/radius#

acct-address X.X.X.X

(where X.X.X.X - RADIUS server IP

address, used for accounting)

WEP-2L(config):/interface/wlan1-va0/vap/radius#

acct-password secret

(where secret - Password for

RADIUS server, used for accounting)

WEP-2L(config):/interface/wlan1-va0/vap/radius#

acct-periodic true

(Enable the periodic sending of

«Accounting» messages to the RADIUS server. By default: false)

WEP-2L(config):/interface/wlan1-va0/vap/radius#

acct-interval 600

(Interval of sending of «Accounting»

messages to the RADIUS server)

WEP-2L(config):/interface/wlan1-va0/vap/radius#

save

6.3.5 Advanced VAP settings:

Enabling VLAN trunk on VAP

WEP-2L(config):/interface/wlan1-va0/vap#

vlan-trunk true

(Enabling VLAN trunk on VAP. To disable, enter

false

)

«
...
50
51
52
53
54
...
»

Summary of Contents for WEP-2L


































































Reviews:

No comments

Related manuals for WEP-2L

Brand: BT Pages: 2

Brand: Cables to Go Pages: 63

Brand: Taylor Made Pages: 12

Brand: DIGITAL YACHT Pages: 6

AirPrime BX3100

Brand: Sierra Wireless Pages: 33

Brand: Ericsson Pages: 12

Ibex-RT-310 Series

Brand: Westermo Pages: 31

Brand: Westermo Pages: 30

Brand: Linksys Pages: 2

Brand: Ubiquiti Pages: 52

Brand: RadioLinx Pages: 99

Brand: Intellinet Pages: 3

Brand: Intellinet Pages: 63

Brand: Intellinet Pages: 84

Brand: Intellinet Pages: 16

Brand: Intellinet Pages: 84

Brand: Sapido Pages: 22

Brand: Sonoff Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands