ELTEX MA4000-PX Operation And Maintenance Manual Download Page 153 | Manualshive

Page: 153 / 181

background image

User Manual, Part V 153

Subscriber access/aggregation node МA4000-РХ

ma4000# show mac pp4 include vlan 30

Mac table (shadow)
~~~~~~~~~~~~~~~~~~
VID MAC address Port Type From To
---- ----------------- ----------------- -------- ------------- -------------
30 a8:f9:4b:82:99:80 port-channel 2 Dynamic Forward Forward
30 a8:f9:4b:82:99:93 port-channel 2 Dynamic Forward     Forward
30 a8:f9:4b:84:e3:40 port-channel 2 Dynamic Forward Forward
30 a8:f9:4b:5a:bc:49 slot-channel 2 Dynamic Forward Forward
4 valid mac entries

ma4000# show mac slot 2 include vlan 2149

Mac table (shadow)
~~~~~~~~~~~~~~~~~~
VID MAC address Port Type From To
---- -----------------   ------------------------- --------   ------------- -------
------
2149      a8:f9:4b:5a:bc:47      plc-pon-port  2/1  (slot  2)            Dynamic        Unknown
Unknown
2149      00:90:1a:42:be:32      plc-slot-channel  2/0  (slot  2)    Dynamic        Unknown
Unknown
2 valid mac entries
ma4000#

40.3

PP4X Interface Status Preview

To view the PP4X interface status, use the

show interface <id> status

command:

PP4X interfaces include: front-port, slot-port.

ma4000# show interface front-port 1/0-5 status
Interface Status Media Speed Duplex Flow control
--------- ------ ----- ----- ------   ------------
front-port 1/0 up copper 1 Gbps full no
front-port 1/1 down none 10 Mbps half no
front-port 1/2 down none 10 Mbps half no
front-port 1/3 down none 10 Mbps half no
front-port 1/4 down none 10 Mbps half no
front-port 1/5 down none 10 Mbps half no
ma4000# show interface slot-channel 0-15 status
Interface Status Media Speed Duplex Flow control
--------- ------ ----- ----- ------   ------------
slot-channel 0 up   none 10 Gbps full no
slot-channel 1 down none 10 Mbps full no
slot-channel 2 down none 10 Mbps full no
slot-channel 3 down none 10 Mbps full no
slot-channel   4 down none 10 Mbps full no
slot-channel 5 down none 10 Mbps full no
slot-channel 6 down none 10 Mbps full no
slot-channel 7 down none 10 Mbps full     no
slot-channel 8 down none 10 Mbps full no
slot-channel 9 down none 10 Mbps full no
slot-channel 10 down none 10 Mbps full no
slot-channel 11 down none    10 Mbps full no
slot-channel 12 down none 10 Mbps full no
slot-channel 13 down none 10 Mbps full no
slot-channel 14 down none 10 Mbps full no
slot-channel 15   down none 10 Mbps full no

«
...
151
152
153
154
155
...
»

Summary of Contents for MA4000-PX






















































































































































































Reviews:

No comments

Related manuals for MA4000-PX

Brand: Xinje Pages: 76

Brand: TC Electronic Pages: 55

nForce 680I LT SLI

Brand: Nvidia Pages: 80

Brand: Commell Pages: 9

Compact Emulator M30620T-CPE

Brand: Renesas Pages: 52

PISO-725 Series

Brand: ICP DAS USA Pages: 8

dspstak 21262sx

Brand: Danville Signal Processing Pages: 35

Brand: Uniden Pages: 5

J-Link-OB-STM32F072-128KB

Brand: Segger Pages: 18

CHEETAH ST34501FC

Brand: Seagate Pages: 68

Brand: Dataprobe Pages: 16

Advanced Flame 1.0

Brand: Eastern Voltage Research Pages: 12

Brand: ADTRAN Pages: 9

Brand: CyberResearch Pages: 59

Brand: Vista Pages: 93

Brand: FDI Pages: 15

Linktropy MINI-G

Brand: Apposite Technologies Pages: 57

Brand: Corsair Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands