ELTEX MA4000-PX Operation And Maintenance Manual Download Page 148

Page: 148 / 181

148

User Manual, Part V

Subscriber access/aggregation node МA4000-РХ

Alarm rate:

Minor

Parameters:

0 – idb ID of port, where errors have been detected.

Name:

MA4000_FAN_FAIL

Description:

Alarm at failure of either of the basket fans.

Alarm rate:

Major

Parameters:

0 – Number of a failing basket fan.

39.2.4

Normalization of Alarms

Name:

MA4000_ALARM_SLOT_OK

Description:

Notification on interface board being in a normal working condition. It clears all other

alarms of MA4000_ALARM_SLOT family for this slot.
Alarm rate: Notify

Name:

MA4000_ALARM_PP4X_UNIT_LOST_OK

Description:

Notification on revealing PP4X unit lost earlier in the basket.

Alarm rate: Notify
Parameters: 0 – number of a found unit;

1 – RH or LH unit is found.

Name:

MA4000_ALARM_SYNC_DISALLOWED_OK

Description:

Notification on allowing configuration synchronization with this unit. It clears alarm

MA4000_ALARM_SYNC_DISALLOWED.
Alarm rate: Notify
Parameters: 0 – number of a unit, with which synchronization is allowed.

Name:

MA4000_FAN_CONTROLLER_FAIL_OK

Description:

Notification on restoring serviceability of fans controller. It clears alarm

MA4000_FAN_CONTROLLER_FAIL.
Alarm rate: Notify
Parameters: Absent.

Name:

MA4000_ALARM_LINK_UP

Description:

Notification

link

appearing

port

PP4X.

clears

alarm

MA4000_ALARM_LINK_DOWN for this port.
Alarm rate: Notify
Parameters: 0 – idb ID of the interface.

Name:

MA4000_PORT_CNTR_ERRORS_FREE

Description:

Notification

discontinued

errors

ports

PP4X.

clears

alarm

MA4000_PORT_CNTR_ERRORS_FOUND.
Alarm rate: Notify
Parameters: 0 – idb ID of a port, where no more errors have been detected.

Name:

MA4000_FAN_OK

Description:

Notification on a fan serviceability restoration. Clears alarm MA4000_FAN_FAIL.

Alarm rate: Notify
Parameters: 0 – number of a fan with restored serviceability.

Summary of Contents for MA4000-PX






















































































































































































Search results

Summary of Contents for MA4000-PX

Reviews:

Related manuals for MA4000-PX

Brands by name

Popular brands

ELTEX MA4000-PX, Operation And Maintenance Manual

Search results

Summary of Contents for MA4000-PX

Reviews:

Related manuals for MA4000-PX

Brands by name

Popular brands