ELTEX MA4000-PX Operation And Maintenance Manual Download Page 147

Page: 147 / 181

User Manual, Part V 147

Subscriber access/aggregation node МA4000-РХ

39.2.3

Alarms

Alarms from MA4000_ALARM_SLOT family are generated in case of non-standard situations with

interface modules in the basket.

All of them feature the following parameters:

0 – slot number

1 – device type code

2 – device version (hw, major, minor)

3 – build of device version

Name:

MA4000_ALARM_SLOT_INVALID

Description:

Alarm occurring when board type in a slot does not correspond to basket configuration.

Alarm rate:

Major

Name:

MA4000_ALARM_SLOT_DOWN

Description:

Alarm in case of link (slot-channel) drop towards interface board.

Alarm rate:

Critical

Name:

MA4000_ALARM_SLOT_ERROR

Description:

Alarm in case of error in connection with interface board. May be caused due to board

pending.
Alarm rate:

Critical

Name:

MA4000_ALARM_PP4X_UNIT_LOST

Description:

Alarm on unplanned loss of one of PP4X units in a basket.

Alarm rate:

Critical

Parameters: 0 – number of a missing unit;

1 – RH or LH unit is lost.

Name:

MA4000_ALARM_SYNC_DISALLOWED

Description:

Alarm when configuration synchronization between PP4X units in a basket is disallowed.

Alarm rate:

Critical

Parameters:

0 – number of a unit, with which synchronization is disallowed.

Name:

MA4000_FAN_CONTROLLER_FAIL

Description:

Alarm at controller fans failure.

Alarm rate:

Major

Parameters:

Absent.

Name:

MA4000_CONFIG_SAVE_FAIL

Description:

Alarm at error of PP4X configuration saving to memory.

Alarm rate:

Major

Parameters:

Absent.

Name:

MA4000_ALARM_LINK_DOWN

Description:

Alarm as a result of link drop on PP4X.

Alarm rate:

Minor

Parameters:

0 – idb ID of the interface.

Name:

MA4000_PORT_CNTR_ERRORS_FOUND

Description:

Alarm at revealing errors at PP4X ports.

Summary of Contents for MA4000-PX






















































































































































































Search results

Summary of Contents for MA4000-PX

Reviews:

Related manuals for MA4000-PX

Brands by name

Popular brands

ELTEX MA4000-PX, Operation And Maintenance Manual

Search results

Summary of Contents for MA4000-PX

Reviews:

Related manuals for MA4000-PX

Brands by name

Popular brands