manualshive.com logo in svg

ELTEX ESR-100, Quick Start And Installation Manual, Page: 12 / 19

Share
Download
ELTEX ESR-100 Quick Start And Installation Manual Download Page 12

 

12

 

ESR series routers

 

3.

 

CONNECTION TO POWER SUPPLY 

1.

 

Ground  the  case  of  the  device  prior  to  connecting  it  to  the  power  supply.  An  insulated 
multiconductor wire should be used for earthing. The device grounding and the earthing wire cross-
section should comply with Electric Installation Code (EIC).  

2.

 

If a PC or another device is supposed to be connected to the switch console port, the device should 
be also securely grounded. 

3.

 

Connect the power supply cable to the device. Depending on the delivery package, the device can 
be  powered  by  AC  or  DC  electrical  network.  To  connect  the  device  to  AC  power  supply,  use  the 
cable  from  the  delivery  package.  To  connect  the  device  to  DC  power  supply,  use  the  cable  with 
cross-section not less than 1mm2. 

4.

 

Turn the device on and check the front panel LEDs to make sure the terminal is in normal operating 
conditions.  

Summary of Contents for ESR-100




















Reviews:

No comments