Eltek Valere Flatpack2 Installation Manual Download Page 3

Page: 3 / 30

Installation Guide

Flatpack2 -48V 150A

~ 2029242 R2, May 2008

Table of Contents

Safety and Compliance................................................................... 5

FCC Compliance Statement.............................................................................................5

Introduction .................................................................................... 7

About This Guide ................................................................................................................7

About This Revision (2) .....................................................................................................7

Mechanical Installation................................................................... 8

System Unpacking.............................................................................................................8

Rack Mounting ....................................................................................................................8

Rack Installation................................................................................................................... 8

Anchor the Cabinet............................................................................................................9

Equipment Rack “Frame Ground”...................................................................................... 9

Converter Shelf Installation.............................................................................................9

Electrical Installation.................................................................... 10

Individual Feed ................................................................................................................. 11

Dual Feed .......................................................................................................................... 11

Module Installation ....................................................................... 12

Distribution ................................................................................... 13

LVD Options...................................................................................................................... 14

Central Office Ground .................................................................................................... 14

Configurations ................................................................................................................. 15

Two Battery, Two Load (2B 2L).......................................................................................15

Two Battery, Two Load, 12 GMT (2B 2L GMT) .............................................................16

Two Battery, Four Load (2B 4L).......................................................................................16

Four Load, 12 GMT (4L GMT) ............................................................................................17

Six Load (6L) ........................................................................................................................17

Breakers and Fuses ........................................................................................................ 18

Plug-in Breakers .................................................................................................................18

Plug-in Fuse Holders..........................................................................................................18

GMT Fuses ...........................................................................................................................20

Battery Connections ...................................................................................................... 20

Load Connections ........................................................................................................... 21

Alarm and Control Terminations .................................................. 22

Alarm Contacts................................................................................................................ 22

Configurable Inputs ........................................................................................................ 23

Temperature Probe Terminations ............................................................................... 23

Symmetry Terminations................................................................................................ 24

Summary of Contents for Flatpack2































Search results

Summary of Contents for Flatpack2

Reviews:

Related manuals for Flatpack2

Brands by name

Popular brands

Eltek Valere Flatpack2, Installation Manual

Search results

Summary of Contents for Flatpack2

Reviews:

Related manuals for Flatpack2

Brands by name

Popular brands