g
g
Teach-in controller:
Press the left button LRN/CLR about
0.5 seconds and then release, the LED
lights up. Send a teach-in telegram from
the controller, the LED goes out.
At teaching in, the confi rmation telegrams
are automatically switched on and sent
with their own ID.
Exit the learn and clear mode immediately
by briefl y pressing the LRN/CLR button.
The routine exits the learn and clear mode
automatically after 60 seconds.
To prevent unintentional teach-in, teach
in pushbuttons by 'double-clicking'
(pressing rapidly twice in succession).
1. Briefl y press the left button LRN/CLR
button 2 times, the LED blinks 2 times
for confi rmation.
2. Select the desired teaching-in function
with the right button.
3. Press the taught-in button with 'double
click'. The LED goes out.
Unencrypted and encrypted sensors can
be taught-in.
Teach in encrypted sensors:
1. Press the left button LRN/CLR for
approximately 0.5 seconds and then
release, the LED lights up.
2. Briefl y press the right button ON/OFF
5 times, the LED fl ashes very excitedly.
3. Enable encryption of the sensor within
120 seconds. The LED goes out.
Attention! The power supply should not
be turned off.
4. Now teach-in the encrypted sensor as
described among teaching-in sensors.
If further encrypted sensors should be
taught-in, go back to point 1.
With encrypted sensors, use the 'rolling
code', i.e. the code changes in each
telegram, both in the transmitter and in
the receiver.
If a sensor sends more than 50 telegrams
when the actuator is not enabled, the
sensor is no longer recognised by the
enabled actuator and you must repeat
teach-in as 'encrypted sensor'. It is not
necessary to repeat the function teach-
in.
Switch on/off repeater:
Press and hold the right button ON/OFF and
plug the FSSA-230V into the socket. Switch
repeater on or off. The LED lights up for
2 seconds to indicate the status = repeater
off (as-delivered state) or for 5 seconds =
repeater on.
Switch on/off confi rmation telegrams:
Press and hold down the left button LRN/CLR
and the right button ON/OFF together and
plug the FSSA-230V in the socket. Confi rma-
tion telegrams are switched on and off. The
LED lights up for 0.5 seconds = confi rmation
telegrams OFF (as-delivered state) or for
2 seconds = confi rmation telegrams ON to
indicate the status.
Confi rmation telegrams:
The FSSA-230V sends a feedback message
containing its own ID to the Eltako wireless
network. The digits 0x70 are sent when the
relay is switched on. The digits 0x50 are sent
when the relay is switched off.
Teach in confi rmation telegrams in other
actuators or in a controller:
Press the right button ON/OFF to change the
switch position and send the con fi rmation
telegram at the same time.
May only be used in closed
dry rooms.
The socket must be easily
accessible.
Don’t insert in a row.
!
Frequency 868.3
MHz
Transmit power
max. 10 mW
Hereby, Eltako GmbH declares that the radio
equipment type FSSA-230V is in
com pliance with Directive 2014/53/EU.
The full text of the EU declaration of
conformity is available at the following
internet address: eltako.com
WEEE-Reg.-Nr. DE 30298319
Must be kept for later use!
Eltako GmbH
D-70736 Fellbach
Technical Support English:
+49 711 94350025
[email protected]
eltako.com
42/2022 Subject to change without notice.
Manuals and documents in further
languages
http://eltako.com/redirect/
FSSA-230V
1. App 2. 3.
www.
