manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 41 / 163

Share
Download
Elster EK280 Applications Manual Download Page 41

EK280 

Application Manual 

39 

 

6.4 

Time-synchronous output 

Each of the outputs 1 to 4 (terminals DA1 to DA4) can be programmed as a time-synchronized output. 

6.4.1 

Parameterization 

Parameterization is carried out via the keyboard on the EK280.  
Alternatively, parametrization can be carried out using the 

enSuite

 program. The paths which are subsequently 

described can be found in 

enSuite

 under "

Parameterize online

" > "

Parameters

". 

a) 

Setting up the output mode: 

 

Move the cursor to the tab "

Serv.

" and subsequently via the following path to the mode for the 

corresponding output 

"

Md.O1

" 

to

 "

Md.O4

"

: 

Serv. 

 Outputs 

 Output 1 

 Md.O1   

Serv. 

 Outputs 

 Output 2 

 Md.O2   

Serv. 

 Outputs 

 Output 3 

 Md.O3   

Serv. 

 Outputs 

 Output 4 

 Md.O4

 

 

i 

The time-synchronized outputs of the EK280 can be operated with active or inactive logic. The 
output mode must be programmed accordingly for this purpose (see below). 

 

Press the ENTER 

 button. The actual parameterized value flashes.

 

 

Press one of the arrow buttons 

 or 

 until the text 

"time sync+" 

(Logic active) or 

"time sync-"

  

(Logic inactive) flashes. 

 

Press the ENTER button to confirm the set value. It is possible to abort the entry by pressing the 
ESC button.

 

d) 

Setting up the source for the output:  

 

i 

Parametrization of the source for the output via the EK280 keyboard is only possible with 
software version 2.20 or later. 
Older software versions may be programmed using enSuite via 

"

Parameterize online

" > 

"

Parameters

"

 and the paths described (see Chapter 6.4.1, 0)  

 

 

 

 

When in the corresponding menu press the

 button until 

"Sc.O1

", 

"Sc.O2

", 

"Sc.O3

", or 

"Sc.O4

" is 

displayed. 

 

Press the ENTER 

 button. The actual parameterized value flashes. 

 

Move the cursor to the digits using the 

 or 

 arrow keys and update them using the 

 or 

 arrow 

keys to a value specified in the table.  

 

Sc.O… 

Description 

01:143_0 

for the beginning of each month at midnight 

02:143_0 

for the beginning of each month at 6am 
The daily limit "6am" (monthly limit) can be changed via 

Serv. 

 Date and time 

 DayB

. 

01:142_0 

for the beginning of each day at midnight 

02:142_0 

for the beginning of each day at 6am 
The daily limit 6am (monthly limit) can be changed via 

Serv. 

 Date and time 

 DayB

. 

01:403_0 

at the beginning of every hour 

 

Press the ENTER button to confirm the set value. It is possible to abort the entry by pressing the 
ESC button. 

 

Summary of Contents for EK280




































































































































































Reviews:

No comments