manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 15 / 163

Share
Download
Elster EK280 Applications Manual Download Page 15

EK280 

Application Manual 

13 

 

Method (without opening the calibration lock): 

 

Open the administrator lock 

 

Move the cursor to 

"Serv." 

>

 "Volume"  >  " Standard volume " >  "Synchronization. Vb > "VbP" 

 

 

Press the ENTER button 

 One digit of the value flashes. 

 

Move the cursor with the arrow buttons 

 or 

 to the digits and change these with the arrow buttons 

 or 

. 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key. 

 

To accept the set value move the cursor to the value "

Store

". 

 

Press the ENTER 

 button 

"0"

 flashes. 

 

Change the value to 

"1"

 by pressing the 

 or 

 arrow keys. 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key. 

 

For 

"Vb"

 is taken 

"VbP"

. 

 

i 

If, with the administrator lock, the take of 

"VbP"

 for 

"Vb"

 is declined with the message 

--

13

--

 the 

procedure has already been once before.  
Further changes are possible when either the calibration lock or the administration lock is open, 
after deleting the change information regarding settings for setting at the same value as 

"Vb"

 (see 

chapter 2.4.5.1). 

 
The following values are shown on the same menu: 

Display 

Description 

TimeX 

Time when counter synchronization was carried out 

Vb_o 

"Old" operating volume counter value Vb 

Vb_n 

"New" operating volume counter value Vb 

 

2.4.5.1  Delete change information for synchronization Vb with the gas meter 

To  allow  for  resetting  of  the  standard  volume  when  the  administrator  lock  is  open,  the  change  information 
regarding setting at the same value as 

"Vb"

 must be deleted: 

 

Open the calibration lock 

 

Move the cursor to tab 

"Serv." 

to

 "Volume" >  "Standard volume" >  "Synchronization Vb > "Clear" .

 

 

Press the ENTER button 

 

"0"

 flashes. 

 

Change the value to 

"1"

 by pressing the 

 or 

 arrow keys. 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key. 

 

"TimeX"

 (time stamp of synchronization), 

"Vb_o"

 (Vb old value), 

"Vb_n"

 (Vb new value) will be set to 

default values. 

2.5 

Parameterize display contrast 

The display contrast of the EK280 can be adjusted to suit the surrounding conditions. 

 

Open the administrator lock as described in the EK280 operating manual. 

 

Move the cursor in tab 

"Serv." 

to

 "Device settings"  >  "Display" >  "Contr."

  

 

Press the ENTER button 

 One digit of the value flashes.

 

 

To enter the display contrast value move the cursor to the digits using the arrow keys 

 or 

 and 

update them using the arrow keys 

 or 

. 

 

i 

The factory settings for the display contrast is 

"164"

. Input values greater than 

"164"

 darken the 

contrast settings, whereas lower values render the display brighter.  
Do not enter any values below 

"100"

 otherwise it is not possible to read values. 

 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key. 

Summary of Contents for EK280




































































































































































Reviews:

No comments