manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 14 / 163

Share
Download
Elster EK280 Applications Manual Download Page 14

EK280 

Application Manual 

12 

 

Method (without opening the calibration lock): 

 

Open the administrator lock 

 

Move the cursor to 

"Serv." 

>

 "Volume" > "Actual volume" > "Synchronization Vm > "VmA" 

(the value 

to be taken over, is first interim saved by the "resettable interim counter" VmP and then taken over 
as "Vm" when the counter reading is reached).

 

 

Press the ENTER button 

 One digit of the value flashes. 

 

Move the cursor with the arrow buttons 

 or 

 to the digits and change these with the arrow buttons 

 or 

. 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key. 

 

To accept the set value move the cursor to the value 

 "Store"

 

 

Press the ENTER 

 button 

"0"

 flashes. 

 

Change the value to 

"1"

 by pressing the 

 or 

 arrow keys.  

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key. 

 

For 

"Vm"

 is taken 

"VmP"

. 

 

i 

If  the  administrator  lock  is  open  and  the  transfer  of  "VmP"  for  "Vm"  is  rejected  with  the 
message 

--

13

--

, this process has previously been carried out.  

Further changes are possible when either the calibration lock or the administration lock is open, 
after deleting the change information regarding setting "Vm" at the same value as the gas meter 
(see chapter 2.4.4.1). 

 
The following values are shown on the same menu: 

Display 

Description 

TimeX 

Time when counter synchronization was carried out 

Vm_o 

"Old" operating volume counter value Vm 

Vm_n 

"New" operating volume counter value Vm 

 

2.4.4.1  Delete change information for synchronization Vm with the gas meter 

Change information for adapting "Vb" to the gas counter must be deleted while the calibration lock is open in 
order to re-set the volume under metering period conditions when the administrator lock is open: 

 

Open the calibration lock 

 

Move the cursor to 

"Serv." 

>

 "Volume" > "Actual volume" > "Synchronization Vm > "Clear".

 

 

Press the ENTER button 

 

"0"

 flashes. 

 

Change the value to 

"1"

 by pressing the 

 or 

 arrow keys. 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key. 

 

"TimeX"

 (time stamp of synchronization), 

"Vm_o"

 (Vm old value), 

"Vm_n"

 (Vm new value) will be set 

to default values. 
 

2.4.5 

Parameterize the volume at base conditions 

 

i 

A one-off setting of the volume counter is possible from software version 2.20 while the 
administrator lock is open. 

 

The quantity converter EK280 offers the possibility of adjusting the standard volume counter once during 
commissioning of the unit while the administrator lock is open. Setting the volume is always possible while 
the calibration lock is open and can also be carried out directly via Standard Volume (tab 

"Serv." 

to 

"Volume" 

> "Standard Volume" > "Vb"

.

 

 
 

 

Summary of Contents for EK280




































































































































































Reviews:

No comments