Elspec G3500 BlackBox User And Installation Manual Download Page 322

Page: 322 / 358

322

Relay Status

The Relay Status screen displays the setup status of the Relays. In order to access the page:-



Open

the screen by selecting

Multi-IO

Relay Status:



The

Relay Status Screen

displays the setup status of the relays:

Definition of the Relay configuration:

Relay 1

Configured to

Auto Mode

, signaled on

Events

, using

0->1->0

as the

Signal

Type

for a

Duration

100ms

. Relay signal is synchronized to

Begin

at the

time the

Condition Ends

SEE ALSO:



About Monitoring And Setting Up your IO Ports













Summary of Contents for G3500 BlackBox







































































































































































































































































































































































Search results

Summary of Contents for G3500 BlackBox

Reviews:

Related manuals for G3500 BlackBox

Brands by name

Popular brands

Elspec G3500 BlackBox, User And Installation Manual

Search results

Summary of Contents for G3500 BlackBox

Reviews:

Related manuals for G3500 BlackBox

Brands by name

Popular brands