ELRO HIS20S Installation & Operating Manual Download Page 20

18

Press              to  exit  Walk  Test  and  return  to  the  top 

level Test Mode menu. 

RF ENVIRONMENT TEST 

Scroll through the top level Test Mode menu until 

RF 

Environment

 ’

 is displayed.   

If the ambient environment is full of radio frequency, an 

indication of 

ENVIRON . . POOR

 ’ 

will be shown 

on the LCD screen.

DIGITAL DIALER TEST 

Scroll  through  the  top  level  Test  Mode  menu  until 

‘DIGITAL DIAL TEST’

 is displayed and press            .   

In  order  to  test  the  digital  dialer  properly,  the 

prerequisite  is  to  set  the  telephone  number,  unit  ID 

number  and  to  turn  on  ‘4-2-1  Monitor  Center’  in  the 

programming  mode.    If  the  telephone  number  is  o.k,

‘TEST….PASS’

  will  be  shown.    If 

‘TEST….FAIL’ 

is

shown with ‘LINE STATUS’ LED flashing, please check 

the telephone line is well connected and retry the test 

again.

When  testing  is  in  progress,  simply  press                to 

stop testing. 

VOICE DIALER TEST 

Scroll  through  the  top  level  Test  Mode  menu  until 

‘VOICE DIAL TEST’

 is displayed and press          . 

In  order  to  test  the  voice  dialer  properly,  the 

prerequisite is to set the telephone number, record the 

message  for  main  and  intruder,  and  to  turn  on  voice 

dial in the programming mode.    If ‘LINE STATUS’ LED 

is  flashing,  please  check  the  telephone  line  is  well 

connected and retry the test again. 

When  testing  is  in  progress,  simply  press                to 

stop testing. 

WIREFREE SIREN SERVICE ON/OFF 

Scroll  through  the  top  level  Test  Mode  menu  until 

‘Wirefree  Siren  Service  ON/OFF’

  is  displayed  and 

press            . 

This offers the flexibility of removing or changing siren’s 

battery.    Wait  for  10  seconds  until  ON/OFF  duration 

has  elapsed,  then  go  ahead  with  fixing  the  siren  as 

desired. 

ALARM TEST 

Scroll  through  the  top  level  Test  Mode  menu  until 

‘ALARM TEST’

 is displayed and press            . 

Scroll  though  the  menu  until  the  required  alarm 

displayed  and  press              to  operate  the  selected 

alarm for 5s. 

Select 

‘Wirefree  Siren  Test’

  to  operate  the  External 

Solar Siren. 

Select 

‘Hardwire  Siren  Test’

  to  operate  the  Smart 

Home  Box  Siren  and  external  hardwired  Siren  (if 

connected). 

Select 

‘Relay Test’

 to operate the External hardwired 

(N.O./N.C.) relay contacts. 

Press              to  exit  Alarm  Test  and  return  to  the  top 

level Test Mode menu. 

DEFAULT SETTINGS 

User Setup 

Admin: 1234 

Password   

User 1~7:   
Not Programmed 

Name 

Admin. User 1~7 

Tel/SMS Remote 

Admin: ON 
User 1~7: OFF 

Latchkey Report 

OFF 

Record User Message 

Not Programmed 

Replay User Message 

Not Programmed 

Remoter 

Not Programmed 

Home Box Setup 

Alarm Time 

180s 

Internal Siren 

ON 

Wire Siren 

ON 

External
Siren

Wireless Siren 

ON 

Summary of Contents for HIS20S































































Reviews: