Do not position a PIR to look directly at a door protected by a Door Contact, this could cause the Door Contact and PIR radio signals
to be transmitted at the same instant when entering, cancelling each other out.
Do not install the PIR completely exposed to direct sunlight.
Avoid installing the PIR in areas where devices may cause rapid change of temperature in the detection area, i.e. air conditioner,
heaters, etc.
Avoid large obstacles in the detection area.
Not pointing directly at sources of heat e.g. Fires or boilers, and not above radiators.
Avoid moving objects in the detection area i.e. curtain, wall hanging etc.
But It is recommended to install the PIR in the following locations:
In a position such that an intruder would normally move across the PIR’s field of
view.
Mount the detector at 2.1 M ~ 2.4 M high for best performance:
<
<
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
N
N
O
O
T
T
E
E
>
>
For the most desired performance of HA2000PP, remember to adjust the height of
HA2000PP mounting site respectively to the height of the tallest animal in the house.
As the taller than average dogs require the HA2000PP to be mounted higher for the
Pet Immunity purpose.
When deciding on the height of the HA2000PP mounting site, remember to take the
possible blind spot into consideration. The blind spot underneath the HA2000PP
enlarges proportionally to the height of the HA2000PP mounting site.
Mount where the animals cannot come to the detection area by climbing on furniture or other objects.
Don’t aim the detector at stairways the animals can climb on.
In a corner to give the widest view.
Where its field of view will not be obstructed e.g. by curtains, ornaments etc.
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
M
M
e
e
t
t
h
h
o
o
d
d
The PIR is designed to be mounted on either a flat surface or in a corner situation with fixing screws and plugs provided.
The base has knockouts, where the plastic is thinner, for mounting purpose. Four knockouts are for surface fixing and four knockouts
are for corner fixing as shown in the picture.
For corner mounting, at user’s own dicretion, an optional triangular bracket is
provided to add Back Tamper Protection. Mount the triangular bracket on he
wall first with the two pointing sticks on top facing you. Then, you can just fit the
PIR onto the hooks of the triangular bracket or screw the PIR onto it.
S
S
u
u
r
r
f
f
a
a
c
c
e
e
m
m
o
o
u
u
n
n
t
t
i
i
n
n
g
g
:
:
Step1.
Remove the fixing screw and cover assembly.
Step 2.
Break through the appropriate knockouts on the base.
Step 3.
Using the holes as a template, drill holes in the surface.
Step 4.
Insert the wall plugs if fixing it into plaster or brick.
Step 5.
Screw the base into the wall plugs.
Step 6.
Screw the cover back onto its base.
C
C
o
o
r
r
n
n
e
e
r
r
m
m
o
o
u
u
n
n
t
t
i
i
n
n
g
g
:
:
Step 1.
Break through the two knockouts on the triangular bracket.
Step 2.
Using the two holes as a template, drill holes in the surface of the corner
Step 3.
Insert the wall plugs
Step 4.
Screw the triangular bracket into the wall plugs with the two pointing sticks on
top facing you.
Step 5.
Fit the PIR onto the hooks of the triangular bracket
Step 6.
If necessary, open the PIR by removing the fixing screw and cover assembly
Step 7.
Break through the appropriate corner fixing knockouts.
Step 8.
Using the corner fixing knockouts as a template, drill holes in the surface in the corner again
Step 9.
Insert the wall plugs if fixing it into plaster or brick.
Step 10.
Screw the base into the wall plugs
Step 11.
Screw the cover back onto its base
S
S
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n
s
s
:
:
Common Technical Specification:
Radio frequency: 868.6-2.5ppm
Modulation/ Demodulation: Narrow band FM @ 15KHz
bandwidth with VCTCXO (Temperature compensated
Crystal)
Sensitivity: >105dbm @S/N +20db
Transmission power: E.I.R.P. -8dbm +-3db
Operation range: 300 meters in open space
Code combinations: 16 777 216 codes
Temperature range:-20°C +45°C
Humidity: up to 90%
PIR Detector HA2000PP
Analysis by Conversion A/N (MSLT), temperature
compensation Protection High Frequencies (magnetic
and radio interferences)
Detection range: 90° over 12 meters, 19 sectors wi th 9
on same line
Supervision: Random 30 min to 50 min
LED light and button: Default & Test Mode.
Transmitted signals: Opening, Closing, Weak battery,
Tamper, Tamper closed, Supervision and Test Mode.
White lens reflecting up à 6000 lux (solar rays, vehicle
beams…)
Double Tamper protection : rear mount + cover
Battery life: Over 3 years assuming 50 transmissions /
day. Roughly 5 years under normal use. 1 month after
weak battery signal. Lithium battery AA 3.6V 2400mAH
Weak battery detection
Dimensions: 93mm (L)*64mm (W)*42mm (H)
