ELOVIS mSPEED smartsensor User Manual Download Page 2

ID308

  

II 

 

DEAR CUSTOMER 

 
Thank you for giving us and our products your trust. Kindly read the operating 
instructions carefully. This is a prerequisite to achieve faultless initial operation 
and functioning of the unit. Before unpacking the equipment, please also read 
the following paragraphs. 
 
 
This unit is a class IIIB laser product and complies with EN60825-1:2001. 
Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to 
Laser Notice No. 50, dated July 26, 2001. 

 
 

 
 
Specifications are subject to change without notice. 

 

CAUTION! Every operation, adjustment or servicing that does not exactly 
conform to the indications given in this instruction manual can result 
in dangerous irradiation from the laser. Servicing of laser appliances 
should be performed by suitably qualified personal only.

 

 

 

The lasers used do not emit X-rays or other harmful radiations. You should however 
use proper caution when handling them. 

 
 

The following safety 
features required to comply 
with the Bureau of 
Radiological Health Class 
IIIB laser requirements are 
included: 
 

 

Laser indicator light on 
controller and laser 
 

 

Delayed laser startup-
laser indicator light on 
prior to laser radiation 
 

 

Laser beam blocking 
device 
 

 

Interlock capability for 
remote shut-off 

INVISIBLE LASER RADIATION - 

AVOID DIRECT EXPOSURE

TO BEAM

INVISIBLE 

LASER CLASS 3B

LASER RADIATION

WHEN OPEN

WAVELENGTH 780nm

CW OUTPUT POWER 25mW

EN 60825-1:2001

Do not open!

No serviceable parts inside!

Summary of Contents for mSPEED smartsensor
























Reviews: