ELNA Elinita EF72 Service Manual Download

Page: 43 / 46

Correct condition
1. Buzzer sounds

2. LCD and LED blink at 1 second

interval.

3. Sewing light turns on.

Press the start/stop key to proceed

to the next step.

Correct condition
Press all of the keys in order.

Each time a key is pressed, the

buzzer sounds, the number is

marked and the name of the key

appears on the LCD.

Press the start/stop key to proceed

to the next step.

Faulty condition
Buzzer does not sound.

The screen does not change.

To replace a part:
Change the printed circuit board A.

Change the printed circuit board F.

Change the printed circuit board K.

Faulty condition
Buzzer does not sound.

The step 1 screen does not appear.

LED of the start/stop key does not

blink.

LCD backlight does not turn on.

Sewing light does not turn on.

To adjust or replace a part:
Change the LED.

Change the LCD.

Change the printed circuit board A.

Change the printed circuit board F.

Change the printed circuit board K.

Step2

01 02 03 04 05 06 07 08 09 10 11 12
13 14 15 16 17 18 19 20 21 22 23 24
25 26 27 28 29 30 31 32

Check key

02 03 04

05 06 07 08 09 10

1112

14 15 16

19 20 21

17 28 18

32 31

Key

1. Function of buzzer, LCD and LED

2. Function of keys

Summary of Contents for Elinita EF72















































Search results

Summary of Contents for Elinita EF72

Reviews:

Related manuals for Elinita EF72

Brands by name

Popular brands

ELNA Elinita EF72, Service Manual

Search results

Summary of Contents for Elinita EF72

Reviews:

Related manuals for Elinita EF72

Brands by name

Popular brands