Configuration and tweaking
For configuration of the 3to unit the
ElMod App
must be connected with connector 4. Turn on the PCB's power supply and start the
ElMod
App
software suite. The
ElMod 3to Truck
will be found within just a few seconds and the current settings will be listed. For further information
about every parameter move the cursor to the parameter's name and wait 1 or 2 seconds. A more detailed text appears.
For configuration of the sound unit the
ElMod App
must be attached to connector 7. Turn on the PCB's power supply and start the
ElMod App
software. The
ElMod 3to Truck
will be found within just a few seconds and the current settings will be listed. For further information about
every parameter move the cursor to the parameter's name and wait 1 or 2 seconds. A more detailed text appears.
SAFETY INSTRUCTIONS
General
- Damage caused by non-observance of these operating instructions will void the warranty! We assume no liability for
consequential damages!
- We accept no liability for damage to property or personal injury caused by improper handling or non-compliance with the safety
instructions! In such cases all warranty claims are void.
- For safety and approval reasons (CE), unauthorized modification or conversion of the device is not permitted. Only use original
spare parts or equivalent spare parts for repairs.
- Make sure that all electrical connections and connections have been made correctly and in accordance with these operating
instructions.
- If the ambient climate changes suddenly (e.g. from a cold room to a warm room), moisture can condense on the unit and
possibly destroy it. Do not operate the unit until it has been acclimatized for about 2 hours.
- Do not operate the device in the vicinity of easily inflammable objects, liquids or gases, danger of explosion!
- Do not expose the device to high temperatures, strong vibrations, high humidity or chemically aggressive environments.
- Operate the device only in a dry environment (below 80 % humidity, non-condensing) and at normal room temperature.
- Do not operate the unit unattended.
- If you have any questions about the operation, safety or connection of the device that are not explained in the operating
instructions, please contact your dealer's support or another specialist.
Electrical hazards
- Supply the device only with low voltage as specified in the technical data. Only use current sources approved for model
making, such as NiMh rechargeable batteries. Operation with voltages higher than 12V is not permitted. There is a fire hazard!
- Observe the limit values for currents as specified in the technical data. Exceeding the permissible values leads to overloading
and destruction of the device and carries the risk of fire or electric shock.
- Installation and connection must only be carried out when the device is disconnected from the power supply.
- Ensure that all connecting cables have a sufficient cross-section.
Heat hazards
- Electronic components on the product can become very hot during operation.
- During installation, ensure that there is sufficient air circulation around the device to prevent overheating due to heat
accumulation.
- During installation, also ensure that there is sufficient distance to heat-sensitive and flammable objects (e.g. wooden and plastic
surfaces, cable insulation).
- Touching the device may burn the skin.
Other hazards
Children can cause all the risks described above due to carelessness or a lack of sense of responsibility. To avoid danger to life
and limb, children under the age of 14 must not install our products. Small children can swallow or inhale the sometimes very
small components with pointed ends. Danger to life! Therefore, do not allow the components to fall into the hands of small
children. In schools, educational institutions, hobby and self-help workshops, the assembly, installation and operation of
components must be supervised by trained personnel. In industrial facilities, the accident prevention regulations of the
Association of Industrial Employers' Liability Insurance Associations for electrical systems and equipment must be observed.
DECLARATION OF CONFORMITY
The product meets the requirements of EC Directive 89/336/EEC on Electromagnetic Compatibility and bears the CE marking for
this purpose.
MANUFACTURER'S NOTE
According to DIN VDE 0869, the person who makes an assembly ready for operation by extension or housing installation is
regarded as the manufacturer and is obliged to supply all accompanying documents when passing on the product and also to
state his name and address.
© ElMod - 20-01-02