Elmo TEB4404 Instruction Manual Download Page 1

T E B 4 4 0 4

I N S T R U C T I O N   M A N U A L

The exclamation point within an equilateral 
triangle is intended to alert the user to the 
presence of important operating and maintenance
 (servicing) instructions in the literature 
accompanying the appliance.

CAUTION

CAUTION :  TO REDUCE THE RISK OF ELECTRIC SHOCK.

    DO NOT REMOVE COVER (OR BACK).
    NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK 

DO NOT OPEN

The lightning flash with arrowhead symbol, within 
an equilateral triangle, is intended to alert the user 
to the presence of uninsulated "dangerous 
voltage" within the product's enclosure that may 
be of sufficient magnitude to constitute a risk of 
electric shock to persons.

CAUTION

Do not use any power supply other than

specified.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

* The CAUTION label is attached on the

bottom of camera.

INFORMATION

This equipment has been tested and

found to comply with the limits for Class A

digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against

harmful interference when the equipment

is operated in a commercial environment.

This equipment generates, use, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications.

Operation of this equipment in a

residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his

own expense.

USER-INSTALLER CAUTION:

Your

authority to operate this FCC verified

equipment could be voided if you make

changes or modifications not expressly

approved by the party responsible for

compliance to Part of the FCC Rules.

Summary of Contents for TEB4404









Reviews: