Elmo st-I200 Service Manual Download

Page: 32 / 40

SOUND (Cont'd)

Case

Step

Point

Remark

Noise is recognized
before Projection

AMP assy
(P7-j)

If AMP assy is inferior, replace.

P-15

Silicon photo diode

(P5-77)

If Silicon photo diode is inferior, replace during

optical recorded film reproduction.

P-17

Noise is recognized
after motor is

started

Cancel coil
(P7-34)

Adjust the position of Cancel coil or if it is
inferior, replace.

Noise is recognized
when sound drum is

rotated

Power IC
(P7-l9)

Replace IC3 (STK-015) if it is inferior at the
same time, replace C32 (0.047 MFD) and R23

(5 ohms).

AMP assy
(P7-j)

Check whether earthed circuit in AMP assy is
either inferior or mid-wired.

P-15

If the input wire to AMP assy is excessively

long and close by the speaker circuit of AMP
assy, cut the wire adequately to prevent

oscillation of AMP assy.

Silicon photo diode
(P5-77)

If Sound drum is touching Silicon photo diode,
adjust the position of Silicon photo holder.

P-17

- 30 -

Summary of Contents for st-I200









































Search results

Summary of Contents for st-I200

Reviews:

Related manuals for st-I200

Brands by name

Popular brands

Elmo st-I200, Service Manual

Search results

Summary of Contents for st-I200

Reviews:

Related manuals for st-I200

Brands by name

Popular brands