background image

- 14 -

SPECIFICATIONS

Model

Power source

Power consumption

Pick-up device

Effective picture element

Scanning area

Scanning system

Scanning frequency

Sync. system

Resolution

S/N ratio

Minimum illumination

AGC

White balance

Backlight control (BLC)

Sens-up

Day/Night

Monitor out

Iris

Iris level adjustment

Lens

Weatherproof specifications

Dimensions

Weight

Ambient temperature

Ambient humidity

Supplied accessories

QNW4000

AC24V  60Hz 0.5Hz

Approx. 5.0w

1/4" Color interline-transfer  CCD

768 (H) X 494 (V)

3.65mm (H) X 2.74mm (V)

2:1 interlaced

LL:15.75kHz (H), 60Hz (V) / INT:15.734kHz (H), 59.94Hz (V)

Line-Lock / Internal (Factory-set at Line-Lock)

470 TV lines (H), 350 TV lines (V)

More than 48dB

1.5lx  (DAY/NIGHT:OFF)
0.3lx  (DAY/NIGHT:ON)

Built-in

ATW

Provided (Factory-set at OFF)

Provided (Factory-set at OFF)

Provided (Factory-set at ON)

RCA VBS 1V (p-p)  75

DC system

Provided

1/4

vari-focal lens

F: 1.4   f: 2.8~5.8

IP54 (When outdoor shade is used)

84 (W) X 75 (H) X 230 (D) mm (3.3 X 3.0 X 9.1 inches)

1.2kg (2.6lbs)

-10

~50

(14 F~122 F)

30

~ 90

Instruction manual
Warranty card
Tripod screws

Note: Weight and dimensions are approximate.

Design and specifications are subject to change without prior notice.

All manuals and user guides at all-guides.com

Summary of Contents for QNW4000

















Reviews: