Elmo CCD Color Video Camera TNC4604 Instruction Manual Download Page 8

- 7 -

PRECAUTIONS FOR USE AND INSTALLATION

* Never aim the camera at the sun.

Never aim or point the camera at the sun even
if you are not shooting.

* Do not shoot intense light.

Strong light such as a spot light on the image
plane will cause blooming or smear. When
strong light comes into the image plane,
vertical stripes may appear on it.  However,
this does not mean that the camera is defect.

* Take precautions when handling a camera.

Do not drop your camera, or give it a strong
shook or vibration. This may cause camera to
malfunction.

* Do not touch internal parts.

Be sure not to touch the internal parts. This
may cause to electrical shock.

* Do not let the camera get wet.

Install the camera at the place where it will
not get wet.
Should it gets wet, turn off the power
immediately and contact your dealer.

* Install your camera where no video noise

appears.
When camera cables have been laid near
electric wires or television receivers, a noise
may interfere the image.
If noise occurs, relocate cables or reinstall
equipment.

* Check the ambient temperature and humidity.

Avoid using camera in areas where
temperature is consistently hotter or colder
than the specified range (See Specifications
chart below) or poor image quality or
damaged parts may occur. Precautions should
also be taken to avoid areas of high humidity.

* Should you notice any trouble.

If any trouble occurs while you are using the
camera, turn off the camera and contact your
dealer. Failure to do so may cause damage to
the camera.

* The socket-outlet should be installed near the

equipment and should be easily accessible.

6X1NHFF02

Printed in CHINA

ELMO (Europe) G.m.b.H.

Neanderstr. 18
40233 Dusseldorf,
Germany
Tel.  0211-376051-53
Fax. 0211-376630
E-mail:[email protected]
Web:http://www.elmo.de/

ELMO Mfg. Corp.

1478 Old Country Road,
Plainview, NY 11803-5034
U.S.A.
Tel.  516-501-1400
Fax. 516-501-0429
E-mail:[email protected]
Web:http://www.elmousa.com/

ELMO Canada Mfg. Corp.

44 West Drive, Brampton,
Ontario, L6T 3T6,
Canada
Tel.  905-453-7880
Fax. 905-453-2391
E-mail:[email protected]
Web:http://www.elmocanada.com/

ELMO CO., LTD.

6-14, Meizen-cho, Mizuho-ku, 
Nagoya, 467-8567 Japan

OVERSEAS SUBSIDIARY COMPANIES

Summary of Contents for CCD Color Video Camera TNC4604









Reviews: