Delete all programming
Keep the programming button pressed down for five seconds. When the light blinks an
alternating red and green the button should be released, and all programming is deleted.
LS Wireless transmitter
for built-in installations
(4 input)
The Wireless transmitter is to be built-in
and used to enable products to send an
input to LS Wireless system.
The transmitter is battery powered and
may be connected with up to four but-
tons. Both short and long button presses
may be transmitted (where light dim-
ming may be required, for example).
The transmitter may be used both for
“stand-alone” Wireless systems and for
LS Controlled systems.
Installation
Application
The Transmitter is mounted hidden and
close to the switches.
Metal surfaces close to the transmitter
can affect the transmission. Avoid
installing the Transmitter in a metal
socket.
Do not install the Transmitter in a
socket containing 230V wires.
1. Insert the battery.
E4 Blå
E3 Brun
E2 Grøn
E1 Rød
Batteri CR 2032
2. Connect the pushbutton to input E1, E2, as
well as E3 and E4, see the Connections and
Pushbuttons section.
3. Program the transmitter (see the section
on programming).
Control link
1
2
3
4
Repeat
1
and
2
for each transmitter which is to be included in the programming.
Short-circuit briefly the wires to the input
which should activate the Control link
(within 5 seconds after step 1).
1
2
A
B
Press programming button
A
once.
Press programming button
A
once.
Diode B will blink RED.
The light diode
lights red.
The light diode
lights red.
1
2
A
B
Conclude the programming by press-
ing programming button
A
once.
All light diodes turn off.
Cancel programming
If you cancel the establishment of a link before the completion of step
4
, you have to wait
until the blinking stops and the link will not be saved.
Receiver
Transmitter
Scenarie link
Press the programming button twice.
1
2
Repeat steps
1
and
2
for each transmitter which is to be included in the programming
for this scenario.
Briefly shortcut the cables for the
input which will activate the Scenario
link (no later than five seconds after
performing Step 1).
3
4
5
The green diode
lights up.
The green diode
blinks.
Receiver
Transmitter
1
2
A
B
Press programming button
A
once.
Diode
B
will blink green.
Repeat steps
3
and
4
for each receiver
which is to be included in the programming for
this scenario.
If the receiver has a light dim-
mer function, the level of dimming
required is set with buttons
1
or
2
. If
the receiver has a relay function, the
required state (on/off) is set with the
same buttons.
1
2
A B
Diode
B
lights up in red for the first
five seconds, and thereafter it will
blink green.
0%
100%
All of the
B
diodes switch off.
1
2
A
B
Complete the process by pushing but-
ton
A
for just one of the receivers.
The transmitter may for example be
built into an ELKO box with an ELKO
switch. This allows the use of an ELKO
switch in a ELKO Wireless installation.
Cancel programming
If you want to cancel the establishment of
a link before you have completed Step
5
,
you should wait for three minutes (until the
blinking lights stop).
Programming
Example
Technical data
In programming a decision is made as to which inputs are to control which
products, and which functions are to be performed. There are two types of pro-
gramming in Wireless, these being the Control link and the Scenario link:
Control link
is used to make Wireless products perform simple executable
functions such as ON/OFF, dim UP/DOWN, Open/Close sun shading, which take
two presses of the button.
Scenarie links
are used to recall an earlier defined lighting scenario with just a
single press of a button.
If the transmitter is to be used together with LS Control, it must be linked to an
LS controller. Linking and programming is carried out in the LS Visual program.
Connections and buttons
Programming
button / Light
diode
There are two cables for each input: one cable is
a plain colour and one is an alternating pattern
of white and one colour which itself is the same
colour as that used on the plain coloured cable.
Red / white-red
Input E1
Green / white-green
Input E2
Brown / white-brown Input E3
Blue / white-blue
Input E4
Grey (short)
Antenna
When the programming for Control link E1/E2
belong together and E3/E4 together and, for
example, they have an ON/OFF function.
Battery
1 piece 3V Lithium, CR2032
Battery lifetime 5 - 7hrs, Depending on use
(approx. 20,000 operations)
Temperature
-5 °C to +50 °C
Humidity
20 % – 95% non-condensing
RF frequency
868 MHz
The product must be disposed
of in accordance with the WEEE
directive on the disposal of elec-
tric and electronic equipment
(Directive 2002/96/EC).
Antenna
Art. nr.: 4706
NB 430
Ver. 1.0
2008.12.08
ELKO AS -
Postboks 234, 1301 Sandvika,
Tlf: +47 67 80 73 00, Fax: +47 67 80 73 01, www.elko.no
ELKO AB -
Box 47020, 100 74 Stockholm,
Tel. +46 84 49 27 00, Fax. +46 84 49 27 30, www.elko.se
ELKO Suomi Oy -
Olarinluoma 9b, 02200 Espoo,
Puh. +358 943 93 210, Fax. +358 943 93 2120, www.elko.fi
EN
®
