Page 2
LZSTL8WS_2D
1000002481 (Rev. C - 11/15)
Installation
For correct and safe installation, please read these instructions completely.
• All Installation work must be performed by an authorized service personnel.
• Disconnect electrical supply serving the Installation area to reduce risk of electrocution.
• Unit not suitable for installations where water jets could be used.
DANGER
WARNING
• Shut off water supply serving the Installation area to reduce risk of water damage.
• Ensure proper ventilation by maintaining clearance from cabinet louvers to wall on each side of Cooler as specified in Rough-In.
• Never wire compressor directly to electrical supply.
• Thoroughly flush all water lines and fittings of all foreign matter before connecting to Cooler.
• Warranty is void if Installation is not made in accordance with current Manufacturing instructions.
CAUTION
• Hose-sets are not to be used for connecting to water mains.
• If inlet pressure is above 100 psig (0.69 MPa), a pressure regulator must be installed in water supply line. Any damage caused by
reason of connecting this product to water supply line pressure outside it’s rated pressure, is not covered by warranty.
• Tools/Items required but not provided.
o Water Shut-off Valve with 3/8” (9.5mm) compression outlet.
o Waste Trap (non-metallic)
o Safety Glasses
o Protective Gloves
o 5/16” (8mm) Hex Socket or Flathead Screwdriver
o 5/32” (4mm) Hex Key
o Fasteners for wall type.
Installation: Cooler Mounting
1. Remove Hanger Bracket (Item 1) fastened to back of cooler by removing one (1) screw.
2. Mount Hanger Bracket as shown in Figure 5, 6, 7, or 8.
• NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support. Anchor
hanger securely to wall using all six (6) 1/4” (6.4mm) diameter mounting holes.
3. Hang Cooler on the Hanger Bracket. Be certain the Hanger Bracket is engaged properly in the slots on the cooler back as shown in
Figure 5, 6, 7, or 8.
4. Remove the four (4) screws holding the lower front panel at the bottom of cooler. Remove the front panel by pulling straight down and set
aside.
Installation: Water Line connection
1. Ensure Mains Water Supply has Water Shut-off Valve with 3/8” (9.5mm) compression outlet.
2. Connect loose end of supplied 3/8” (9.5mm) unplated copper tube to Water Shut-off Valve.
• NOTE: If 3/8” (9.5mm) copper tube must be cut for proper fit, remove all burrs from the outside of tube and re-flush before use.
3. Install waste trap. Remove the slip nut and gasket from the waste trap and install them on the cooler waste line making sure that the end of
the waste line fits into the waste trap. Assemble the slip nut and gasket to the waste trap and tighten securely.
• IMPORTANT: If it is necessary to cut the drain, loosen the screw at the black rubber boot and remove tube, check for leaks after
reassembly
4. It is recommended that the waste trap be insulated to avoid excessive condensation due to chilled water running through the waste trap.
5. Install filter cartridge. Remove filter from carton, remove protective cap, and attach filter to filter head by firmly inserting into head and rotating
filter clockwise.
• IMPORTANT: DO NOT TURN ON WATER BEFORE INSTALLING BOTTLE FILLER
Installation: Bottle Filler
1. Remove two (2) mounting screws holding top cover to bottle filler with a 5/32” (4mm) Hex Key (See Figure 2). Remove top cover. Note: Do not
discard mounting screws; they will be needed to re-install top cover.
2. Remove wall mounting plate from bottle filler. Place wall plate against wall on top of basin. Center the wall plate side to side with the basin. Mark
the six (6) mounting holes with a pencil. See Figure 5, 6, 7, or 8.
3. Remove the wall mounting plate from wall.
Note:
Mounting plate
MUST
be supported securely. Add fixture support carrier if wall will not provide
adequate support.
4. Install wall mounting plate to wall using six (6) 7/16” (11.1mm) obround mounting holes (mounting bolts not provided). See Figure 1. Use
appropriate fasteners for your wall type.
5. Feed 3/8” (9.5mm) water line through hole in tower/basin gasket. See Figure 3.
6. Install gasket on bottom of bottle filler tower with gasket support bracket, (2) washers, and (2) screws. See Figure 4.
7. Feed modular (C-13) end of International Power Cord Set up through basin hole and hole in gasket. Connect to Power Inlet on Bottle Filler. Do
not plug into electrical outlet.
8. With the power cord and waterline through the hole on top of water cooler place bottle filler on three (3) angled tabs protruding from the wall
mounting plate installed on wall. Make sure round boss in gasket fits in hole of basin.
9. Once bottle filler is installed on wall plate tabs, waterline, wires, and power cord are installed properly, push top of bottle filler toward wall and
line up two (2) holes on top cover.
10. Re-install top cover on bottle filler (See Figure 2) with two (2) mounting screws from step 1 above.
Caution
: Do not over tighten screws.
11. Install remaining tube insulation to the water line from bottle filler, connect bottle filler waterline inside of the water cooler by connecting the 3/8”
(9.5mm) waterline to the tee.