background image

754747-100

11

Fill whirlpool with warm water and add two teaspoons of powdered automatic dishwasher (not laundry) 
detergent and one-half cup of household bleach to filled whirlpool.

Activate whirlpool system in accordance with operating instructions and run system for two minutes.

Drain and refill whirlpool with cold water. Circulate for five minutes.

Drain whirlpool completely after step 3 (above) is completed.

Your Eljer whirlpool is designed to give you many years of pleasure with reasonable care and maintenance.

Your new acrylic bathtub is tough, durable and easy to care for. The colors have been formulated to match other
Eljer fixtures and enhance your choice of bathroom decorations. The high gloss surface will retain its lasting luster with
proper care and maintenance.

CLEANING AND MAINTENANCE:

  •  Always fill the tub with temperate water. Excessively hot water (greater than 130˚ F) may cause surface damage.

  •  Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.

  •  Clean after use with a mild liquid household detergent cleaner. Do not turn on jets when such cleaners are present.

     
  Do not use:

 Lestoil® Cleaner; Lysol® Disinfectant (spray or concentrate); or Lysol® Basin, Tub and Tile Cleaner;

  Windex® Cleaner; Mr. Clean® Cleaner; Dow® Disinfectant Bathroom Cleaner*; or other cleaning products in
 aerosol 

cans.

HARSH CHEMICALS, SHARP AND ABRASIVE OBJECTS 

SHOULD NEVER BE USED ON ACRYLIC SURFACES

• Do not use wire brushes, knives or sharp objects to remove stains or other surface blemishes.

• Use of abrasive cleaners or powders will dull the surface. If the glossy surface loses its sheen, dulled areas can 

be partially restored by rubbing with a white automotive body polishing compound and waxing with a liquid wax. 

    Do not wax surfaces where you walk or stand.

• Do not allow nail polish remover, acetone, dry-cleaning fluid, paint remover, or other solvents to come into contact 
    with the surface.

• Clean the surrounding surface immediately after using caustic drain cleaners. 

    Do not permit drain cleaner to enter circulation system.

• Burning cigarettes will irreparably damage the surface of the whirlpool.

CLEANING/PURGING THE CIRCULATION SYSTEM

Once every month the circulating system must be purged and cleaned.  Follow the steps outlined below:

1.

2.

3.

4.

For Troubleshooting and Repair Parts please log on to www.eljer.com

* Lestoil® is a registered trademark of The Clorox Company.
   Lysol® is a registered trademark of The Linden Company.
   Windex® is a registered trademark of S.C. Johnson and Son, Inc.
   Mr. Clean® is a registered trademark of The Proctor and Gamble Company.
   Dow® is a registered trademark of The Dow Chemical Company.

Summary of Contents for 2932J048













Reviews: