background image

Rev. 20220302DT DS0169 

 

www.elitescreens.com

 

 

 

VMAX Tab-Tension 3 Series

 

Electric Wall/Ceiling Tab-Tensioned Projection Screen

  

User’s Guide 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Thank you for your purchase of an Elite Screens VMAX 3 Series Electric Projection Screen. 

 
 
IMPORTANT SAFEGUARDS 

Read these instructions carefully and retain them for future use. If this product is passed to a third party, 
then these instructions must be included. 

 

Caution: 

The  screen’s  Black  Top  Drop  is  already  set  to  its  maximum  drop  distance. 

There is NO extra Black Top Drop in the roller. Please be aware of this as it will void your 
warranty with Elite Screens

™. Unapproved changes or modifications (except for cutting 

the  power  cord  for  hardwire  installations)  to  this  unit  are  prohibited  and  will  void  your 
warranty. 
 

 

To  avoid  damaging  the  unit,  do  not  use  with  any  unauthorized  accessories  not  recommended  by  the 
manufacturer.  

 

Handle the unit carefully during transportation to avoid any damages. 

 

To ensure safe and reliable operation, direct connection to a properly grounded power source is advised. 

 

The power outlet supplying power to the unit should be close to the unit and easily accessible. 

 

Do not install the unit on uneven or inclined surfaces. 

 

Do not put heavy objects on the power cord and position it properly to avoid creating a trip obstacle. 

 

Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short circuit. 

 

There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself. No one 
except authorized technicians can open and make repairs to this unit. 

 

Make sure the power source this unit is connected to has a continuous power flow. 

 

If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to avoid 
overheat. 

 

Do not handle the power plug when your hands are wet or your feet are in contact with water. 

 

Do not use this unit under the following circumstances. 

 

Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning. 

 

Avoid direct Sunshine, rain shower and moisture. 

 

Keep away from fire sources and high temperature to prevent this device from overheating. 

 

Cut off the power supply first before transportation or maintenance. 

 

Fully disconnect from the power supply when the unit is not in use for a long period of time, as 
should be done with any other electric household appliance. 

 

To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is 
obvious damage or if there are any evident broken parts. 

 

 
 

Summary of Contents for VMAX Tab-Tension 3 Series






Reviews: