manualshive.com logo in svg

Elite Screens AEON series, User Manual, Page: 7 / 8

Share
Download
Elite Screens AEON series User Manual Download Page 7

04202021JA    SN 211M +                                    

www.elitescreens.com

                        

U-00197 

7

 

 
 
 
 
 

 

 

Step 12

: Install the 

angle cover

 (

n

) on each corner of the frame using the 

M4x4 screws (m)

. 

Note: The angle cover screws holes align with the screw holes on the elbow joint.  

 

 

 

 

 

 

 

Step 13

: Install the

 springs (q) 

in each middle area to further support the bezel trim edge frame.

 

 

 

 

 

 

 

 
Wall Installation 

Step 14: 

Measure the overall length and height of the frame and drill holes for the  top brackets. Line up the wall 

brackets  with the  drilled  holes  on  the installation  location  and  screw them  in  using  a  Phillips  screwdriver.  If  not 

installing  into  a  structural  wood  stud,  use  a  hollow  wall  anchor  then  screw  in  the  M5x50  wood  screws  with  a 

screwdriver. Make sure the brackets are leveled. 

 

 

 

 

 

 

 

 

 

Model/Size 

X = Wall bracket distance 

X1 = Bracket hole distance 

Y = Top/Bottom Wall Bracket Height 

92’’ 

1100mm (43.30”) 

30mm (1.18”) 

980mm (38.58”) 

100’’ 

1200mm (47.24”) 

30mm (1.18”) 

1080mm (42.52”) 

110’’ 

1300mm (51.18”) 

30mm (1.18”) 

1210mm (47.64”) 

120’’ 

1400mm (55.12”) 

30mm (1.18”) 

1330mm (52.36”) 

125’’ 

1400mm (55.12”) 

30mm (1.18”) 

1400mm (55.12”) 

 

Don’t lock the screw to the bottom. 

j. 

k. 

n. 

Tear off the double-sided tape.

 

q. 

Diagonal Sizes of 150” and below use 4 x wall brackets

 

Summary of Contents for AEON series









Reviews:

No comments