background image

 

24 

them and keeping them. 

  
Expansion wall plugs are provided to secure the hood to most 
types of walls/ceilings. However, a qualified technician must 
verify suitability of the materials in accordance with the type of 
wall/ceiling. The wall/ceiling must be strong enough to take 
the weight of the hood. 

Do not tile, grout or silicone this 

appliance to the wall. Surface mounting only. 

  
  

 

Operation 

   

Control panel with 6 buttons 

 
To select the functions of the hood just touch the commands. 
 

 

Light key ON/OFF 

 

 

Intensive speed selection key

(suction 

power) - duration 5 minutes

the hood sets this 

power and at the end of the 5 minutes returns 
to the previous setting. 

 

High-speed selection key 

(suction power). 

 

Medium-speed selection key

(suction power) 

- when flashing it indicates the need to wash or 
replace the carbon filter. This signal is normally 
deactivated. To activate the alarm, disable the 
electronic by pressing the 

0

button for 3 

seconds.  
Next, simultaneously press buttons 

1

 and 

2

for 

3 seconds; at first, only button 

1

will flash, then 

both buttons 

1

 and 

2

 will flash to indicate 

activation. Repeat the procedure to deactivate 
the alarm; at first buttons 

1

 and 

2

will flash and 

subsequently only button 

1

 to indicate 

deactivation. 

 

Low-speed selection key

 (suction power) –

when flashing it indicates the need to wash the 
fats filter. 

 

Motor key OFF

 (stand by) – excludes the 

electronics – reset wash/replace filters signals. 

MOTOR OFF 

 

Press briefly to switch the motor off. 

RESET FILTERS SIGNALS

 

In functioning mode, after carrying out filter 
maintenance, press the key until hearing the 
sound signal. The flashing LED 

(grease filter) 

or 

(carbon filter) stops flashing. 

EXCLUDING THE ELECTRONICS

 

Press the key for 3 seconds. The hood 
command electronics will be excluded. 
This function can be useful during the product 
cleaning operations. 
Just repeat the operation to reinsert the 
electronics.  

 
If the hood fails to operate correctly, briefly disconnect it from 
the mains power supply for almost 5 sec. by pulling out the 
plug. Then plug it in again and try once more before 
contacting the Technical Assistance Service. 
  

 

Summary of Contents for ELPRF0124234





















Reviews: