ELGO Electric P8511 Series Short Description Download Page 34

Page: 34 / 34

Liability exclusion / Guarantee

We have checked the contents of this instruction manual carefully, to the best of our knowledge and belief for

conformity with the described hardware and software. Nevertheless errors, mistakes or deviations can not be excluded,

therefore we do not guarantee complete conformity. Necessary corrections will be included in the subsequent editions.

We appreciate your ideas and improvement suggestions very much. Reprint, duplication and translation, even in

extracts, are only allowed with a written authorization by the company ELGO Electric GmbH. We constantly strive for

ELGO Electric does not assume any liability for possible errors or mistakes.

The guarantee period is one calendar year from the date of delivery and includes the delivered unit with all

components. ELGO Electric GmbH will at its option replace or repair without charge defects at the unit or the included

parts, verifiable caused by faulty manufacturing and/or material in spite of proper handling and compliance to the

instruction manual.

Damages verifiably not caused by ELGO Electric GmbH and due to improper handling are excluded from any guarantee

e.g. by applying faulty voltage, diffusion of liquid into the interior of the engine, using force, scratching the surface,

chemical influences etc.!

Subject to modifications © ELGO Electric GmbH 2004

Summary of Contents for P8511 Series



































Search results

Summary of Contents for P8511 Series

Reviews:

Related manuals for P8511 Series

Brands by name

Popular brands

ELGO Electric P8511 Series, Short Description

Search results

Summary of Contents for P8511 Series

Reviews:

Related manuals for P8511 Series

Brands by name

Popular brands