background image

CAUTION:

IMPORTANT:

Read the entire instrution manual before you start installation and assembly. 

If you have any questions regarding any of the instructions or warnings, Please 

contact at [email protected] for assistance.  

Use with products heavier than the rated weights indicated may result in 

instability causing possible injury.

Ensure that you have received all parts according to the component checklist prior to 

installation. If any parts are received damaged or defective, please contact us at 

[email protected]. We are happy to replace parts to ensure you have a fully 

functioning product.

• Mounts must be attached as specified in assembly instructions. Improper installation 

may result in damage or serious personal injury.

• Safety gear and proper tools must be used. This product should only be installed by 

professionals.

• Make sure that the supporting surface will safely support the combined weight of the 

equipment and all attached hardware and components.

• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

• This product contains small items that could be a choking hazard if swallowed. Keep 

these items away from children.

• This procuct is intended for indoor use only. Using this product outdoors could lead to 

product failure and personal injury.

PRODUCT LINE GRAPH

75mm 100mm 114mm

75mm

100mm

114mm

±180°

±90°

m

m5

14

xa

m

~5

31

ni

m

min10~max85mm

100mm

min10~max85mm

50mm

170mm

min220~max275mm

±180°

±135°

+45°

-45°

60mm

Summary of Contents for ELTGM05-2











Reviews: