background image

SCHEMATIC DIAGRAM

QUIZ

1. The Sound Activated Switch consists of a transistor amplifier, a transistor switch and _______ types of digital

circuits.

2. A ____________ is created when hands are clapped together.

3. A one-shot is also called a _____________ multivibrator.

4. When triggered, the first one-shot will remain at a logic 0 for ______ second(s).

5. When both inputs of NOR gate U2A are at a logic 0, the output will be at a logic ______.

6. A flip-flop is also called a _____________ multivibrator.

7. A flip-flop is a circuit whose output __________  __________ changes when a pulse is applied to the input.

8. The voltage needed at the input of the NOR gates to switch the outputs from one state to the other is between

______ and ______ volts.

9. When current flows through an LED, it will emit ____________.

10. The transistor amplifier is a ____________ emitter amplifier set at a gain of ________.

+

+

+

Answer

s:

1.tw

o;2.

wa

vef

orm;

3.monostab

le;4.

0.25;5.

1;6.

bistable;

7.logic le

vel;

8.4.5, 5.5;

9.light;

10.common, 50

FOIL SIDE OF PC BOARD

Elenco

®

Electronics, Inc.

150 Carpenter Avenue

Wheeling, IL  60090

(847) 541-3800

Fax: (847) 520-0085

Website: www.elenco.com • e-mail: [email protected]

Summary of Contents for K-36









Reviews: