background image

Space War Gun

K-10

Rapid fire or single shot with 2
flashing LEDs.

0-15V Power Supply

K-11

A low-cost way to
supply voltage
to electronic
games, etc.

0-15VDC @ 300mA
8.5VAC @ 500mA

Christmas Tree

K-14

LED Robot Blinker

K-17

You’ll have fun displaying the
PC board
robot.
Learn about
free-running
oscillators.

Digital Bird

K-19

You probably have never heard
a bird sing this way before.

Nerve Tester

K-20

Test your ability to remain calm.
Indicates failure by a lit LED or
mild shock.

Yap Box

K-22A

This kit is a hit
at parties.
Makes 6
exciting
sounds.

Burglar Alarm

K-23

Alarm for your car, house, room,
or closet.

Whooper Alarm

K-24

Can be used as a sounder or
siren.

Metal Detector

K-26

Find new money and old
treasure.  Get started in this
fascinating hobby.

Pocket Dice

K-28

To be used with any game of
chance.

FM Microphone

AK-710/K-30

Learn about microphones,
audio amplifiers, and RF
oscillators.  Range up
to 100 feet.

Telephone Bug

K-35

Our bug is only the size of a quarter,
yet transmits both sides of a
t e l e p h o n e
conversation
to any FM
radio.

Sound Activated Switch

K-36

Clap and the light comes on . . .
clap again and it goes off.

Lie Detector

K-44

The sound will
tell if you are 
lying.  The
more you lie,
the louder the 
sound gets. 

Motion Detector

AK-510

Use as a sentry,
message
minder, burglar
alarm, or a
room
detector.

Two IC AM Radio

AM-780K

New design - easy-to-build,
complete radio on a single PC
board.  Requires 9V battery.

Transistor Tester

DT-100K

Test in-circuit transistors and
diodes.

Variable Voltage DC

Power Supply Kit
0-15VDC

XP-15K

Ideal for students,
technicians, and
hobbyists.
Great for
breadboarding.

Auto-scan FM Radio Kit

FM-88K

Unique design - two-IC FM
receiver with training course.

EDUCATION KITS

Complete with PC Board and Instruction Book

Requires 9V battery

Requires
9V battery

Requires
9V battery

Requires
9V battery

Requires

9V battery

Requires
9V battery

Requires 9V battery

Requires
9V battery

Requires
9V battery

Requires 2
“AA” batteries

Training course incl.

No batteries
required!

Requires 9V battery

Requires
9V battery

Requires
9V battery

Requires
9V battery

Produces flashing
colored LEDs
and three
popular
Christmas
melodies.

Requires
9V battery

-14-

Requires
9V battery

Summary of Contents for FG-500K

















Reviews: