Elenco Electronics EP-130 Manual Download Page 9 | Manualshive

Page: 9 / 160

Elenco Electronics EP-130 Manual Download Page 9

-9-

Switch: You know what a switch is - you use it to
connect or disconnect electrical circuits. When you
slide the switch to the correct position, the circuit is
complete, allowing electricity to flow through it. In
another position, the switch causes a break in the
circuit’s path, so that the circuit is not complete and
electricity cannot flow through it. The switch we’re
using is a double-pole, double-throw switch; this
means it can connect one pair of terminals to either
of two other pair of terminals. You will learn how this
works later on.

Key: The Key is a very simple switch - press it and
the circuit allows electricity to flow through it.
Release it and there is a break in the circuit’s path,
so the circuit is not complete. You will use the key in
many circuits, most often in the signaling circuits (to
send Morse code, and so on).

Terminals: You will use the two terminals (13 and 14)
in some projects to make connections to external
devices, such as the earphone, an antenna or earth
ground connection, special sensor circuits, and so on.

Wires: You will use the wires to make connections
between terminals.
The parts and spring terminals are mounted onto a
platform. If you look underneath it you can see how
wires are used to connect the parts and their
terminals.

BUILDING YOUR FIRST PROJECT

There is a simple wiring sequence listing for each
project. You should connect appropriate length wires
between the terminals listed in each grouping.
Always use the shortest wire that will do the job.
When you come to a new grouping (separated by a
comma), connect the terminals in that group.

Here’s an example:

Project 1 has the following wire sequence listing:

1-29, 2-30, 3-104-106, 4-28-124, 5-41-105, 27-88,
75-87-103-40, 115-42-119, 76-116, 121-122.

You should connect a wire between 1 and 29,
another between 2 and 30, another between 3 and
104, and then another between 104 and 106. So, you
continue until all connections are made.

Caution:

In each wiring sequence, we’ve

deliberately left an important power wire connection
as the last connection. It is important that you make
this last connection LAST. With some circuits, if you
complete one part of the electronic circuit before
another, a transistor or another part can be
damaged. So, follow the wiring sequence exactly.

«
...
7
8
9
10
11
...
»

Summary of Contents for EP-130

































































































































































Reviews:

No comments