elem 5411074191481 Original Instructions Manual Download Page 45

 

Turn off the product using the isola- 
tor switch: 

– before clearing a blockage, 
– before checking, cleaning or working  
on the machine, 
– before storage 
– if the machine vibrates abnormally  
(stop and check immediately), 
– after striking a foreign object. Inspect  
the machine for damage and get ad- 
vice on necessary repairs from your  
ELEM GARDEN TECHNIC Service Centre : 

[email protected]

 

 

Maintenance  

=

Always wear gardening gloves  

when handling or working near the  
sharp blades. 

=

Before working on the mower, turn  

it off using the isolator switch. 

=

Before working on the docking sta- 

tion or power supply, remove plug  
from mains. 
 

Clean the exterior of the machine thor- 
oughly using a soft brush and cloth. 

Do  

not use water, solvents or polishes.

  

Remove all grass and debris, especially  
from the ventilation slots. 
Turn the machine on its back and clean  
the blade area regularly. Use a stiff  
brush or scraper to remove compacted  
grass clippings.  

Keep all nuts, bolts and screws tight  

to be sure that the machine is in safe  
working condition. 

Periodically visually inspect the ma- 

chine and replace worn or damaged  
parts for safety. 

Ensure that only official ELEM GARDEN 

TECHNIC replacement parts are used. 

Replace all blades and bolts as a set  

as required. 

Winter Storage and Transportation 

Turn off the machine using the iso- 

lator switch. 

The robot mower will operate between 5 °C  

and 45 °C. During the winter season  
once the temperature in the garden is  
consistently below 5 °C store the ma- 
chine and the docking station in a se- 
cure, dry place, out of the reach of  
children. 
Do not place other objects on the mow- 
er or docking station. 
It is recommended to use the original  
packaging when transporting the Inde- 
go over long distances. 
The mower can also be stored using the  
Robot mower storage bag accessory. 

Store the machine only within a tem- 

perature range between –20 °C and  
50  °C. As an example, do not leave  
the machine in the car in summer. 
 

Battery Hazards 

Recharge only in the ELEM GARDEN 

TECHNIC approved docking station. 

The robot mower will operate between 5 °C  

and 45 °C. If the battery temperature  
is outside this range the robot mower will  
display a message and will not leave  
the docking station. If operating it will  
return to the docking station or stay  
on place. 

In the unlikely event of liquid being  

ejected from the battery avoid all  
contact with the machine. If contact  
with the liquid occurs, seek medical  
advise. 

If the battery becomes defective, liq- 

uid can escape and come into contact  
with adjacent components. Check  
any parts concerned and contact the  
ELEM GARDEN TECHNIC Service Centre. 
 

Summary of Contents for 5411074191481
































































































Reviews: