Flasher control:
Some new bikes need a flasher indicator lamp. Just take simple 2 diodes (1N4007 or similar) and
connect the cathodes, (ring side) together and connect it to your indicator lamp. The other sides of the diodes can be
connected to the flasher outputs. Thats it...
+ 12 Volt input from ignition lock (big red cable):
This is the 12 volt power input for the box and the power outputs.
The outputs of the box are self resettable in the case of a short circuit. However,
we recommend to wire a 15 Ampere
fuse
in the line, cause the temperatures in the case of a short circuit will reach about 120 degree C what might result in
small flaws in the plastic housing and a possible loose of the water protection.
Adjustment of the different functions:
The D - Box can be use for the most circumstances without any modification on the box. However, you can easily change
some functions in the box without to be a software specialist. Just press the "horn" button while switching on the ignition
switch and you are in the "setup mode". An one time emergency flash will indicate the "Mode 1". This ist just a small
show function. The flashers will flash 2 times when switching on the ignition switch. Just feel free to press the "right"
button if you like to activate this function. Alternatively you can switch off this function by pressing the "left" button and
you will come immediately to "Mode 2" what is indicated with 2 flashes of the direction lamps. Feel free to continue to
make your personal settings for your bike. All settings are stored in the box after 8 times pressing the "left" or "right"
button. Your done! ...it´s that simple... The D - Box will keep your settings after a power off. However, you can change
the settings at every time you want. The following options are possible:
Number of
flashes
Mode
Left flasher button
Right flasher button
Describtion
1 x
Show flasher
Off
On
2 emergency flashes when
power on the box
2 x
Flasher auto off
Off
On
The flasher will switch off
after 20 or 40 times
3 x
Flasher auto off
20 flashes
40 flashes
Number of repeats when
"Flasher Auto" is on
4 x
Low Light
On
Off
The flashers will glim with
about 25 % when the
flasher function is off
5 x
Brake light mode
Only brake light
Brake light / rear light
combination
The rear light will glim with
40 % when the brake light
switch is not pressed
6 x
Start / Stop
1 pushbutton
2 pushbuttons
You can use one or two
buttons for the start and
stop functions
7 x
Headlight - switch
or button
Switch
Pushbutton
The box can handle a
headlight switch or a push
button.
8 x
Flasher control
Switch
Pushbutton
The flasher can controlled
by push button or by a
switch
Installation:
The power outputs can work with currents between 3 and 6 Ampere for each output. The maximum current of the whole
D - Box is 20 Ampere due to the small size of the box. So, please take care that the 12 Volt power to the box is protected
with a 15 or 20 Ampere fuse. The cables to the buttons should be more than 10 cm away from the ignition and spark plug
cables (if possible) in order to prevent the box against emv disturbances. Otherwise the D - Box might can do some
"funny" unwanted functions like changing the light, switching on the flashers, etc. It´s also a good idea to use shielded
cables to the push buttons if available. A shielded standard CAT 6 cable without connectors for example should be
available in every local computer shop and the cost is (almost) nothing.
The D - Box was developed for an implemenation in show bikes and racing bikes. It should be installed by professional
well trained engineers only. Please check your local regulations regarding the traffic light rules in your country before of
the use of the D - Box in your bike. Please be aware that we are not responsible for any hazards, damages or
disadvantages due to the use of the electronicbox. The electronicbox devices are registered under the number
DE54933725 WEEE as B2C device. We also declare that the D - Box is conform to the CE and ROHS regulations for the
European market.
We tried to keep the functions of the D - Box and this manual as simple as possible. If you have any questions while the
installation please don’t hesitate to contact us at
elektronikbox.de
We wish you to have a lot of fun with your new D - Box in your bike and
of course always a safely trip!
2 / 2
