background image

10

Maintenance and cleaning

Before starting maintenance or cleaning, switch off the unit and withdraw the 
mains plug. 

Wipe over unit and dust-collector compartment if necessary with a damp cloth 
and allow to dry. Do not use abrasive materials or solvents. Clean floor nozzle and 
brush webs occasionally with the crevice nozzle.

Do not wash the dust collector in a dishwasher or clean with aggressive detergents.

(This could damage or dull the dust collector).

What to do if...

...it is difficult to move the nozzle:

 reduce the suction capacity. This does not 

reduce the cleaning effect.

...the motor overheating protection has switched off the unit: 

e.g. owing to 

overload of the motor, by full dust collector or blocked tools. 

Switch off the unit, withdraw the mains plug, allow motor to cool. Check dust col-
lector, suction tube and suction hose; removed any blockage. The unit can be swit-
ched on again after approx. 30 minutes.

...the fuse has blown: 

the fuse can blow if other electrical units with high con-

sumption are used at the same time as the vacuum cleaner from the same circuit. 
In this case before switching on set the suction capacity control to the lowest level 
and only select a higher level after switching on.

For the sake of the environment

Do not simply discard packing material and used units!

Unit packing

: we recommend preserving the packing material for the term of the 

warranty to permit reliable transport.

Take the polyethylene (PE) bag to a PE recycling bank.

Recycling the vacuum cleaner at the end of its service life:

 the plastic parts are 

identified by a material code, so that they can be recycled at the end of the service 
life of the vacuum cleaner in the same way as other materials.

Your local authority environment office will provide information on the location of 
the nearest recycling facility.

Spares

New filters, dust bags, brush rollers and drive belts can be obtained from Authori-
sed Electrolux Dealers and electrical retailers. If difficulty is experienced in obtai-
ning spares please call us on 08706 055055.

Summary of Contents for Z5305













Reviews: