manualshive.com logo in svg

Electrolux Z4700 Series, Owner'S Manual, Page: 15 / 16

Share
Download
Electrolux Z4700 Series Owner'S Manual Download Page 15

  Problem 

Cause 

Solution

  Motor will not start. 

Electric Plug 

•  Push plug securely into outlet. 

   

 

•   Try another outlet. 

   

 

•   Check circuit breaker. 

   

 

•   Refer to page 3.

  Motor suddenly stops.  

Thermal Cut Off 

•   Refer to page 13.

  Does not clean the carpet/floor. 

Dust Cup  

•  Empty the dust cup.

   

 

•   Make sure dust cup is installed properly and 

dust cup latch is secured.

   

Filter 

•  Make sure pleated filter is clean. 

   

Belt  

•   Replace broken, loose, out-of-shape belt.

   

Brushroll 

•   Clean hair and thread from bristles and end 

cap area. 

   

 

•   Replace brushroll if bristles are worn. 

   

Hose 

•   Remove any clogs from the hose that restrict 

the air flow. 

   

 

•   Refer to pages 11, 12, and 13.

  No suction at the hose. 

Dust Cup and Filter 

•   Empty the dust cup.

   

 

•   Clean and install filter properly. 

   

 

•   Make sure dust cup is installed properly and 

dust cup latch secured.

   

Hose 

•   Remove any clogs from the hose that restrict 

the air flow. 

   

 

•   Check both ends of the hose. 

   

 

•   Refer to pages 11 and 13.

  Noise from the brushroll area. 

Brushroll 

•   Remove hood and clean debris from the 

brushroll area. 

   

Belt 

•   Replace broken, loose, out-of-shape belt.

   

 

•   Refer to page 12.

  Cleaner is hard to push. 

Cleaner Height Setting 

•  Put handle in operating position. Tilt the 

cleaner back to raise the front wheels off the 

floor. Then turn the knob to a higher setting. 

   

 

•   Refer to page 9.

  Cleaner height knob will not turn. 

Cleaner Height Setting 

• 

Hint: 

Put handle in operating position. Tilt  the 

cleaner back to raise the front wheels off the 

floor. Then turn the knob.

   

 

•   Replace broken, loose, out-of-shape belt.

   

 

•   Refer to pages 9 and 12.

   Brushroll will not turn. 

Brushroll 

•   Remove hood and clean debris from the 

brushroll area.

   

 

•   Refer to page 12.

  Burning smell. 

Belt 

•   Remove hood and clean debris from the 

brushroll and belt area.

   

 

•   Refer to page 12.

  Stair brush doesn't work. 

Brushroll/Belt 

•  Remove any clogs from the opening or debris 

around the brushroll or belt.

   

 

•   Refer to page 14.

  Missing parts. 

 

•  Call Electrolux on 08445 614614. Call to this 

number will be charged at 5p per minute 

at all times from a BT Landline. Have the 

model and serial numbers ready when you 

call. See rating plate beneath the cleaner. 

  More questions?

15

PROBLEM SOLVING

Summary of Contents for Z4700 Series

















Reviews:

No comments