manualshive.com logo in svg

Electrolux Wascator W100, Service Manual

Share
Download
Electrolux Wascator W100 Service Manual Download Page 67

Service
Manual

12

Type

Page

Edition

Function checks

It is possible to test the machine's various functions
by inputting a numerical code using the key set.
The function chosen can then be turned on and off
using the start button. Program indicator no. 10
shows if the function is turned on or off.

The table below lists the functions which can be
simulated and which numerical codes apply to each
respective function.

Code

Functions

11

Detergent compartment 1

12

Detergent compartment 2

13

Detergent compartment 3

14

Detergent compartment 4

15

Detergent compartment 5

16

Valve connection, hot water

17

Valve connection, cold water

18

Valve connection, hard water

19

Heat (The display window shows the
machine temperature and not code "19").

21

Motor, clockwise rotation

22

Motor, counter-clockwise rotation

23

Distribution, counter-clockwise

24

Spin, counter-clockwise

25

Coupling

26

Drain valve

27

Drain

28

Level switch

N.B.!

When code 19 is pushed in, the temperature
is displayed, not the code number.

Disconnecting service program

•

Return the service switch on the programmer
circuit board to the N position.

11

3

12. Fault Tracing

1416

WARNING!

Do not run the motor (codes 21
and 22) immediately after spin.
Wait until the drum has stopped to
avoid major risk of damaging
machine.

N

S

Fig.

5

9002

5

Service switch

to left = service position

to right = normal position

Summary of Contents for Wascator W100







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands