Electrolux Smart Promix Service Manual Download Page 20

Page: 20 / 28

Messages and Error codes

(Valid to june 2013)

Messages

Cause

Action

The pan is not in working position.

The grid is fully or partly open.

Overheating of heating element.
The heat will shut off in the event
of a fault to the element sensor.

STOP

has been pressed during

operation.

Overloaded agitator

Interrupt in PT-1000 sensor

Short circuit in PT-1000 sensor

Interrupt in PT-1000 sensor

Short circuit in PT-1000 sensor

Fault in water meter

no water in to the pan

Manual water filling

in progress

The boiling pan has been without

power /the emergency button is

pressed.

SVI, SPI, during cooling, the boiling

pan has become de-energized.

Red LED in START

flashes. The following

text appears in the display:

TILTING
Xh XXmin XXX°C

ATOR 000rpm

AGITATOR
LID/GRID ON

Buzzer sounds and the following text appears
in the display:

ELEMENT
OVERHEATED

INTERRUPT?
YES  PRESS  STOP
NO  PRESS  START

The agitator has stopped. The following text
appears in the display:

OVERLOADED
SHUT-OFF BOILING PAN
DURING APPROX 1 MIN

PT-1000 FOOD
INTERRUPT

PT-1000 FOOD
SHORT CIRCUIT

PT-1000 ELEMENT
INTERRUPT

PT-1000 ELEMENT
SHORT CIRCUIT

WATER

INTERAPTION

SET  WATER
UNSETTABLE  DURING
WATER  FILLING

The Reset button is lit

Red LED in the START button is lit. Boiling is
selected.
The boiling pan does NOT heat up.

Press Tilt return

Close the grid and press Agitator start

•Press On/Off

. The display goes out.

•Wait 5 seconds!
•Press On/Off

. Display lights.

If the warning is still lit:
•Press On/Off

to close the pan.

The display goes out.
See Warning! Overheating and contact authorised personnel.

Follow the instructions in the display.
• Press STOP

to stop.

or
• Press START

to return to the program.

• Press On/Off
The display goes out.
Wait for approx 1 minute
Increase agitator speed
or
Reduce the amount of food in the pan

•Press On/Off

. Display lights.

Contact authorised personnel.

Press STOP

to interrupt the manual water filling.

Reset the emergency stop and push the reset button.
If the boiling pan has been de-energized wait approximately 20s,
then push the reset button. Still failure, contact service person-
nel.

Start the COOLING program and stop it after approximately
20 seconds.
Restart the BOILING program.
Only boiling pans with Ice-water cooling.

Summary of Contents for Smart Promix





























Search results

Summary of Contents for Smart Promix

Reviews:

Brands by name

Popular brands

Electrolux Smart Promix, Service Manual

Search results

Summary of Contents for Smart Promix

Reviews:

Brands by name

Popular brands