manualshive.com logo in svg

Electrolux Side by Side Refrigerators, Service Manual

Share
Download
Electrolux Side by Side Refrigerators Service Manual Download Page 5

4

SECTION G - ICE & WATER DISPENSER

Ice Dispenser Container & Rail Assembly ................................................................................................ 65

Dispenser Auger Motor & Solenoid Assembly ................................................................................... 65

      To Remove Auger Motor ........................................................................................................... 65

     To Test Auger Motor ................................................................................................................. 65

      To Remove Solenoid Assembly ................................................................................................ 65

     To Test Solenoid Assembly ....................................................................................................... 66

      To Remove Lamp Socket & Light Bulb ...................................................................................... 66

Ice Auger & Crusher Assembly ............................................................................................................. 66

To Replace Crusher Blades ............................................................................................................ 66

Ice & Water Dispenser Assembly .......................................................................................................... 67

Feature Levels ............................................................................................................................... 67

Seven Selection Dispenser ............................................................................................................. 67

Five Selection Dispenser ................................................................................................................ 67

Four Selection Dispenser ................................................................................................................ 67

Three Selection Dispenser .............................................................................................................. 67

Ice & Water Only ........................................................................................................................... 68

To Gain Access to Control Area ............................................................................................................ 68

Models With Electronic Control ............................................................................................................. 69

Fast Freeze - Fast Ice .......................................................................................................................... 71

Voltage Testing ................................................................................................................................... 73

To Remove Control Board..................................................................................................................... 74

SECTION H - WATER SYSTEM

Water Systems .................................................................................................................................... 75

Water Valve ........................................................................................................................................ 75

PureSource Water Filters ...................................................................................................................... 75

Water Tanks ........................................................................................................................................ 76

To Test The Water Fill System ............................................................................................................. 78

APPENDIX A

Connecting Ice Maker To Water Supply ................................................................................................. A2

Automatic Ice Maker Tips ..................................................................................................................... A3

APPENDIX B

Exploded Views Index .......................................................................................................................... B1

Cabinet ......................................................................................................................................... B2

Freezer Door ................................................................................................................................. B3

Refrigerator Door ............................................................................................................................ B4

Shelves ........................................................................................................................................ B5

Controls with Front Filter ................................................................................................................. B6

Controls with Rear Filter ................................................................................................................. B7

System ......................................................................................................................................... B8

Ice Maker ...................................................................................................................................... B9

Ice Dispenser ................................................................................................................................ B10

Electronic Ice Dispenser ................................................................................................................. B11

Ice Container ................................................................................................................................. B12

Wiring Diagram .............................................................................................................................. B13

Performance Data .......................................................................................................................... B15

Notes............................................................................................................................................ B16

Summary of Contents for Side by Side Refrigerators





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands