If the refrigerator is not cold enough it may be because:
1. The ventilation is inadequate owing to reduced area of
the ventilation passages (partial blockage of grilles from
wire mesh etc).
2. The evaporator is frosted up.
3. The temperature control setting is incorrect.
4. The gas pressure is incorrect - check the pressure regu-
lator at the gas container.
5. The ambient temperature is too high.
6. To much food is loaded at one time.
7 . The door is not properly closed or the magnetic sealing
strip is defective.
8. More than one source of energy is used at the same
time. If the refrigerator still does not work properly, call a
service technician.
MAINTENANCE
Concerning gas- and electric installations, only authorized
experts are allowed to carry out maintenance and repair
works. Besides, it is recommendable to contact an authori-
zed service if it comes to repair works.
According to the valid regulations G607 of DVGW, the gas
installation as well as the connect flue oulets are to be
checked every two years by an expert (this has to be
arranged by the person responsible).
SOME USEFUL HINTS
Make sure that:
●
The refrigerator is not operating on 12 V when the ve-
hicle is parked, otherwise you will drain the car bat-tery in
a short time.
●
Defrosting is carried out periodically.
●
The refrigerator is left with the door(s) ajar when it is not
to be used for some time.
●
Liquids or items with a strong odour are well packa-ged.
●
The ventilation openings are unobstructed.
●
The door is secured by means of the travel catch when
the caravan is on the move.
●
Only one mode of operation at a time is used to run the
refrigerator.
GUARANTEE AND SERVICE
The refrigerator is guaranteed for one full year on condition
that it is used in a correct manner and in accordance with
these operating and installation instructions.
It is also embraced by a European guarantee as described
in the brochure supplied with the refrigerator.
Service and spare sparts are obtainable from your dealer or
Electrolux - consult the telephone directory
TECHNICAL DATA
Overall dimensions, refrigerator . . . RM4400/4401
Height
. . . . . . . . . . . . . . . . . . . . . . . .805 mm
Width
. . . . . . . . . . . . . . . . . . . . . . . .525 mm
Depth (incl. cooling unit)
without door. . . . . . . . . . . . .494 mm
with door. . . . . . . . . . . . . . . .533 mm
Build-in dimensions
Height
. . . . . . . . . . . . . . . . . . . . . . . .810 mm
Width
. . . . . . . . . . . . . . . . . . . . . . . .530 mm
Depth
. . . . . . . . . . . . . . . . . . . . . . . .510 mm
Capacity
gross
. . . . . . . . . . . . . . . . . . . . . . . . 103
lit.
net
. . . . . . . . . . . . . . . . . . . . . . . . . 92
lit.
frozen food compt . . . . . . . . . . . . . . . . 12
lit.
Weight (without packaging) . . . . . . . . . . . . . 28
kg
Electrical data
Input 230 V . . . . . . . . . . . . . . . . . . . . . 125 watt
12 V . . . . . . . . . . . . . . . . . . . . . 120 watt
Energy consumption /24 h. . . . . . . . .2,7 kWh
LP gas data
Input
. . . . . . . . . . . . . . . . . . . . . . . . 232 watt
ditto, low flame . . . . . . . . . . . . . . . . . . 105 watt
Energy consumption /24 h. . . . . . . .0,27
kg
Cooling medium Ammonia (R 717)
INSTALLATION INSTRUCTIONS
REPOSITIONING THE HINGES
The door hinges can be moved to the opposite side in the
following way:
●
Unscrew the upper hinge pin, taking care not to lose the
set of washers and bushes.
●
Lift the door from the lower hinge pin.
●
Unscrew the pin and mount it on the opposite side hinge.
●
Unscrew the travel catch and mount it on the opposite
side.
●
On the upper edge of the door are two plastic inserts for
the alternative holes of the travel catch. Pry out carefully
and exchange
●
Fit the door on the pin and reassemble the pin with
washers and bushes in its new place.
●
Check that the door closes properly and seals all round.
DOOR PANEL
The door panel can easily be mounted or changed. The
dimensions of the panel must be:
......................... RM 4400/4401
Height ................................. 724 mm
Width .............................. 492,5 mm
Thickness ........................... 3,2 mm
●
Remove the door, see REPOSITIONING THE HINGES.
●
Remove the lower trim moulding and then withdraw the
panel by sliding it downwards.
●
Fit new panel in place and slide it up as far as possible.
●
Fit the trim moulding back in place.
The sealed cooling system must not be opened, since
it is under high pressure.
10
