CARING FOR YOUR MULTI TRIM
After you have finished using your Flymo Multi-Trim
follow the procedure below:
•
AVOID ACCIDENTAL STARTING. REMOVE PLUG
FROM MAINS AND KEEP FEET AWAY FROM THE
SWITCH LEVER WHEN:- CLEANING AROUND
THE INSIDE OF THE SAFETY GUARD, REMOVING
OR REFITTING SPOOL CAP, MANUALLY FEEDING
OR REPLACING NYLON LINE. (SEE FIGS U & V)
1.
Disconnect from the mains electricity supply.
2.
Never clean your trimmer with water, cleaning
fluids, or solvents, just remove debris with a
suitable tool, a soft brush or dry cloth.
3.
Using the scraper provided (Multi Trim 200), clean
around the inside of the safety guard to remove
any grass and debris.
(Fig W)
.
4.
Using a soft brush, clean around the inside of the safety
guard, the cutting head and the motor housing.
(Fig X)
.
5.
Inspect the trimmer carefully, especially the parts of
the cutting head.
6.
If your trimmer is damaged in any way contact your local
Electrolux Outdoor Products approved service centre.
•
Never use a damaged trimmer.
7.
Wind cable carefully to avoid kinking.
8.
Store in a cool, dry place and out of reach of children.
ENVIRONMENTAL INFORMATION
Electrolux Outdoor Products are manufactured under an
Environmental Management System (ISO 14001) using,
where practical, components manufactured in the most
environmentally responsible manner, according to
company procedures, and with the potential for
recycling at the end of the products’ life.
•
Packaging is recyclable and plastic components have
been labelled (where practical) for categorised recycling.
•
Awareness of the environment must be considered
when disposing of ‘end-of-life’ product.
•
If necessary, contact your local authority for disposal
information.
SERVICE RECOMMENDATIONS
•
Your product is uniquely identified by a silver and black product rating label.
•
We strongly recommend that your product is serviced at least every twelve months, more often in a
professional application.
GUARANTEE AND GUARANTEE POLICY
If any part is found to be defective due to faulty manufacture
within the guarantee period, Electrolux Outdoor Products,
through its Authorised Service Repairers will effect the repair or
replacement to the customer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken apart
or tampered with by any person not authorised by Electrolux
Outdoor Products.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used outside of the country for
which it was specified.
(i)
The machine has not been used commercially.
*
This guarantee is additional to, and in no way diminishes the
customers statutory rights.
Failures due to the following are not covered, therefore it is important
that you read the instructions contained in this Operator's Manual
and understand how to operate and maintain your machine:
Failures not covered by guarantee
*
Replacing Nylon Line.
*
Failures as a result of not reporting an initial fault.
*
Failures as a result of sudden impact.
*
Failures as a result of not using the product in accordance
with the instructions and recommendations contained in this
Operator's Manual.
*
Machines used for hire are not covered by this guarantee.
*
The following items listed are considered as wearing parts
and their life is dependent on regular maintenance and are,
therefore not normally subject to a valid warranty claim:
Nylon Line, Electric Mains cable.
*
Caution!
Electrolux Outdoor Products does not accept liability under the
warranty for defects caused in whole or part, directly or indirectly
by the fitting of replacement parts or additional parts that are not
either manufactured or approved by Electrolux Outdoor
Products, or by the machine having been modified in any way.
SPOOL CAP AND NYLON LINE (2 LINES) - T
T1-a - Cap, T1-b - Cap Release Latch, T1-c - Spool,
T1-d - Spoolholder, T1-e - Slot,
T2-a - Upper Section, T2-b - Lower Section
To remove spool cap
1.
Press and hold in the two cap release latches.
(T1).
2.
Pull
cap away from the spoolholder.
(T1).
When refitting the spool cap
1.
Keep all areas of the cap and spoolholder clean.
Failure to do so may prevent the cap being securely
located in the spoolholder.
2.
Replace the cap,
pressing firmly DOWN
towards
the spoolholder to ensure cap is fully located.
3.
Check that the cap is correctly fitted by trying to
remove it without depressing the two latches.
To replace nylon line.
For your convenience it is recommended you buy spool
and line complete. Nylon line only is also available. Both
are available from Electrolux Outdoor Products stockists.
To fit spool and line complete:
1.
Remove the cap.
2.
Remove old spool.
3.
Place spool into spoolholder.
4.
Release line from cleat (if 2 lines are fitted release
only one line).
5.
Secure line into slot
(T1)
.
6.
Repeat for second line.
•
Ensure spool is fully located by gently rotating it
during fitment, whilst keeping the spoolholder
steady.
7.
Refit the cap.
To fit nylon line only:
•
Remember !
Your Flymo Trimmer is designed to
use only nylon line with a maximum diameter of
1.5mm. Use only genuine Flymo nylon line.
1.
IF YOU HAVE TWO LINES FITTED
IMPORTANT - If your trimmer has 2 lines fitted
always wind the line onto the upper section of
the spool first.
Take approximately 5 metres of line. Insert 15mm of
line into one of the holes in the upper section of the
spool
(T2)
and wind line in the direction of the
arrows on the top of the spool. Leave
approximately 100mm of line unwound and place
into cleat as illustrated in figure
T3
. Repeat on
lower section of spool.
2.
Care should be taken to ensure that the line is
neatly coiled on the spool. Failure to do so will
impair the efficiency of the automatic line feed.
3.
Then fit spool as described in
‘To fit spool and line
complete’
, section above.
ENGLISH - 4
