How to trim and edge
WARNING
•
The use of eye protection is recommended. Do not
lean over the trimmer whilst trimming or edging,
objects may be thrown by the cutting line. Do not
allow cutting head to rest on the ground. Do not
overload your trimmer. Overloading can be avoided
by making sure the motor speed does not drop
unduly. Disconnect from the mains electricity supply
before attempting any maintenance or adjustment.
BEFORE USE
•
Make sure that the line is fed out.
•
Make sure motor is up to full speed before
trimming or edging.
To start your trimmer
•
The switchbox is provided with a lock-off button
(M1) to prevent accidental starting.
1. To start, press lock-off button
(M1)
, squeeze the
switch lever
(M2)
, release lock-off button.
How to trim
1. Cut with nylon line at an angle using the tip.
(N)
2. Swing trimmer in and out of the cutting area taking
small cuts
(O)
3. Line is fed out automatically every time the trimmer
head stops rotating and returns to operating speed.
•
Extra line can be fed out manually.
4. To stop your trimmer release the switch lever
(M2)
.
How to edge
1. To convert to edging mode, depress locking button
and twist head anti-clockwise until arrow lines up
with "EDGE". An audible "click" will confirm that the
head is locked. Ensure the button has returned to its
original position.
(P)
2. Rest edger on roller for extra stability and line up
with edge of lawn.
(Q)
. Edge in direction indicated in
Fig R.
so that debris is thrown away from you.
3. To return to trimming mode, depress locking button
and twist head clockwise until arrow lines up with
"TRIM". An audible "click" will confirm that the head
is locked. Ensure the button has returned to its
original position.
(S)
.
Spool Cap
To remove spool cap
U1 - Cap, U2 - Spool, U3 - Spool holder,
U4 - Manual line feed button, U5 - Eyelet
1. Press and hold in the two cap release latches.
(T1)
2. Pull cap away from the cutting head.
(U)
When refitting the spool cap
1. Keep all areas of the cap and spoolholder clean.
Failure to do so may prevent the cap being securely
located in the spoolholder.
2. Align the two latches on the cap with the two
windows in the spoolholder, then press down into the
locked position.
3. Ensure the two cap release latches are clearly visible
and are fully engaged with the windows in the
spoolholder.
4. Check that the cap is correctly fitted by trying to
remove it without depressing the two latches.
Nylon Line
To manually feed the nylon line
If required, line can be fed out manually. To operate,
gently pull on the line whilst at the same time alternately
pressing and releasing the button, on the side of the
spoolholder.
(V)
Do not depress the button more than three times.
Excessive line will snag the line cutter and cause
the trimmer to malfunction.
To replace nylon line.
Replacement nylon line is available
from most Electrolux Outdoor Products stockists. You can
buy it either as spool and line complete, or as nylon line
only.
To replace spool and line (complete)
1. Take new spool and remove tape holding line in place.
2. Unwind approximately 100mm of line and feed this
through eyelet,
(W1)
, then drop the spool into
spoolholder
smooth side uppermost
.
To replace nylon line on spool.
X1 - Hole in spool, X2 - Line
1. Take line and insert into hole in spool.
2. Turn spool clockwise to wind on required amount of
line, (approx. half = 10m) and cut line to length,
(X)
.
Care should be taken to ensure that the line is
neatly coiled on the spool. Failure to do so will
impair the efficiency of the automatic line feed.
3.
Leave approximately 100mm of line unwound and
feed this through eyelet,
see fig W
, then drop the
spool into the spoolholder
smooth side uppermost
.
•
Ensure spool is fully located by gently rotating it
during fitment.
•
Remember ! Your Flymo Cordless Trimmer is
designed to use only nylon line with a maximum
diameter of 1.5mm. Use only genuine Flymo
nylon line.
Caring for your Cordless Trimmer
After you have finished using your Flymo trimmer follow
the procedure below:
•
Avoid accidental starting. Keep your hands and
fingers away from the switch lever while inspecting,
cleaning or carrying out any maintenance work.
•
Keep fingers and hands clear of line cutter on
leading edge of guard
.
1. Never clean your trimmer with water, cleaning fluids,
or solvents, just remove debris with a suitable tool,
a soft brush or dry cloth.
2.
Using the scraper provided, clean around the inside of
the safety guard to remove any grass and debris.
(Y1)
3. Using a soft brush, clean around the inside of the
safety guard
(Y2)
, the cutting head
(Y3)
and the
motor housing.
(Y4)
4. Inspect the trimmer carefully, especially the parts of
the cutting head.
5. If your trimmer is damaged in any way contact your
local Electrolux Outdoor Products approved service
centre.
•
Never use a damaged trimmer
6. Store in a cool, dry place and out of reach of
children.
Service Recommendations
•
Your product is uniquely identified by a silver and black product rating label.
•
We strongly recommend that your product is serviced at least every twelve months, more often in a
professional application.
ENGLISH - 3
