www.electrolux.com
6
Power off
Power down the product by gently touching the
ON/OFF icon on the center of the product.
Child lock
To enable CHILD LOCK by long pressing ON/OFF
icon for 5 seconds, and numerical display shows
LOC for 3 seconds. After 3 seconds the LOC text
dissapear and IAQ appears. LOC text reappear
when during child lock any of the controls are
touched. When in this mode, no other icon will
register input (ref. picture 7).
12
13
UV-C emitter control
Activate the UV feature by gently touching UV
icon on the product, and the UV-C emitter will
light on. The UV-C emitter can help eliminate
bacteria in the product. (ref. picture 11).
Touch the button again to turn off the UV feature.
11
Sleep mode
Chose the SLEEP mode by gently touching " "
icon on the product. In SLEEP mode unit will
operate at the low noise level and all indicators
except for SLEEP icon will go off. (ref. picture 10).
Air speed control
Change the fan speed by gently touching desired
fan speed icon on the product. You can also slide
your finger across the arc to change fan speed
(ref. picture 8).
Auto mode
Chose the AUTO mode by gently touching "A" icon
on the product. In AUTO mode the unit will adjust
operation according to latest air quality (PM2.5
level). (ref. picture 9).
10
8
9
AIR QUALITY INDICATOR
The appliance has an air quality sensor that
analyzes the air quality.
The air quality light will show the real-time air
quality through different colors of light. As shown
below:
14
LIGHT'S COLOR
Blue
Green
Orange
Red
PM 2.5 (μg/m
3
)
AIR QUALITY
0-15
Very Good
16-35
Good
36-75
Bad
>75
Very Bad
FILTER CHANGE INDICATOR
The filter change indicator will light up to
remind you to change the filter.
• When filter change indicator flicker with red
light, please replace the filter and reset the filter
change indicator.
• When filter change indicator stop flicker and the
red light fix, please replace the filter immediately
and reset the filter change indicator.
15
16
Filter change indicator reset operation
Press the filter change button " "for 3s and filter
change indicator will reset, then red light will go off.
UV-C EMITTER REPLACEMENT
The UV indicator will blink to remind you to
change the UV-C emitter.
Please replace the UV-C emitter as following
steps (ref. picture 12) and reset the UV change
indicator.
Caution: The appliance must be disconnected
from the supply before replacing the UV-C
emitter.
1&2. Open the product by rotating the base
in anticlockwise direction with the handle
provided at the bottom.
3. Remove the filter from the unit.
4. Grasping the UV-C emitter with a clean cloth
or a tissure and pulling straight out of the unit
carefully.
17
Caution: After filter is installed correctly, please
ensure product is placed on a level surface
before proceeding further. Ensure there is
enough free space on top of and around the
product.
OPERATION
Connect the power plug.
Power on
Power on the product by gently touching the
ON/OFF icon on the center of the product
(ref. picture 7).
6
7
Install the filter
Carefully insert the filter back into the product
without the plastic packaging (either end of the
filter works). Take care that the filter is placed in
the center of the cavity (ref. picture 4).
Close the base
Close the product by rotating the base in
clockwise direction with the handle provided at
the bottom till it is securely in place. There two
opposing triangular marks on the base of the
product to identify the leading edge for turning
(ref. picture 5).
4
5
To disable CHILD LOCK, long press ON/OFF icon
again for 5 seconds till the LOC text dessapear
and IAQ appears.
Install the UV-C emitter.
Grasping the UV-C emitter with a clean cloth or a
tissure and inserting it in carefully. (ref. picture 3).
3
packaging from the unit and break open the
plastic bag and discard appropriately.
(ref. picture 2).
