Electrolux EU 5730I Installation And Instruction Manual Download Page 6

17

MAINTENANCE

Unplug the appliance before carrying out

any maintenance operation.

Warning

This appliance contains hydrocarbons in its cooling
unit; maintenance and recharging must therefore
only be carried out by authorized technicians.

Periodic cleaning

Clean the inside with warm water and bicarbonate of
soda.

Rinse and dry thoroughly.

Clean the condenser (black grill) and the
compressor at the back of the appliance with a
brush or a vacuum cleaner. This operation will
improve the performance of the appliance and save
electricity consumption.

Periods of non-operation

When the appliance is not in use for long periods,
take the following precautions: 

remove the plug from the wall socket;

remove all food;

defrost and clean the interior and all accessories;

leave the door ajar to allow air to circulate to prevent
unpleasant smells.

Defrosting

The freezer compartment, however, will become
progressively covered with frost. This should be
removed with the special plastic scraper provided,
whenever the thickness of the frost exceeds 4 mm.
During this operation it is not necessary to switch off
the power supply or to remove the foodstuffs.

However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
and it is advisable to carry out this operation when
the appliance is empty.

To carry out complete defrosting of the freezer

compartment  

proceed as follows:

1. pull out the plug from the wall socket or turn the

thermostat knob to the Ç

È setting;

2. remove any stored food, wrap it in several layers

of newspaper and put it in a cool place;

3. leave the door open, insert the plastic scraper in

the appropriate seating at the bottom centre,
placing a basin underneath to collect the defrost
water;

4. when defrosting is completed, dry the interior

thoroughly and refit the plug; keep the scraper for
future use;

5.  turn the thermostat knob back to the required

setting or replace the plug in the power socket.
After letting the appliance run for at least half an
hour, replace the previously removed food into
the compartment.

D068

Important: 

Never use sharp metal tools to scrape off frost
from the evaporator as you could damage it.

Do not use a maechanical device or any artificial
means to speed up the thawing process other
than those recommended by the manufacturer.

A temperature rise of the frozen food packs,
during defrosting, may shorten their safe
storage life.

s

Summary of Contents for EU 5730I












Reviews: