manualshive.com logo in svg

Electrolux ESL5391, Operating Instructions Manual

Share
Download
Electrolux ESL5391 Operating Instructions Manual Download Page 26

26

What to do if...

Remedying small malfunc-
tions

If the acoustic signal is activated, warning tones
sound if there are faults.
If one of the following fault codes is displayed in the
multi-display during operation:

–

Fault code

Å 10

 (Problems with water inlet),

–

Fault code

Å 20

 (Problems with water drainage),

please have a look at the following table.

When the fault is remedied, press the cycle selection
button. The cycle will continue.

With other fault codes (“

Å

” followed by a number): 

–

Abort the dishwashing cycle. 

–

Switch the appliance off and on again. 

–

Re-set the dishwashing cycle. 

If the fault is displayed again, please contact the
Customer Care Department and inform them of the
fault code.

Malfunction

Possible cause

Remedy

1 short warning tone

 continu-

ously repeated can be heard,
the cycle indicator for the selected 
dishwashing cycle is flashing:
fault code 

Å 10

 is displayed in the 

multi-display:
(Problems with water inlet)

Water tap is blocked with limescale 
or faulty.

Check the water tap and have it re-
paired if necessary.

The tap is turned off.

Turn the tap on.

The filter (where present) in the 
threaded hose fitting on the tap is 
blocked.

Clean the filter in the threaded hose 
fitting.

Filters in the base of the dishwash-
er compartment are blocked.

Press the button for the commenced 
dishwashing cycle;
then abort the dishwashing cycle 
(see section: Starting a dishwashing 
cycle);
clean filters (see section: Cleaning 
the filters). 

Water inlet hose
has not been correctly positioned.

Check the position of the hose.

2 short warning tones

 continu-

ously repeated can be heard.
The cycle indicator for the select-
ed dishwashing cycle is flashing,
fault code 

Å 20

 is displayed in the 

multi-display. (Problems with wa-
ter outflow)

The sink outlet is blocked.

Clean out sink outlet.

Water drain hose
has not been correctly positioned.

Check the position of the hose.

3 short warning tones

 continu-

ously repeated can be heard,
Fault code 

Å 30

 is displayed in 

the multi-display.

The anti-flood system has been 
triggered.

First shut off the water tap, then 
switch off the appliance and contact 
the Customer Care Department.

Summary of Contents for ESL5391









































Reviews:

No comments

Brands by name

Popular brands

Load more brands